• 23.05.2012, 13:39
  • Register
  • Login

  • You are not logged in.

 

Regulate manually the Aquastream XT

HollowMac

Newbie

Posts: 4

Regulate manually the Aquastream XT

Thursday, February 19th 2009, 4:08pm

Hello,

Excuse me if my english is bad, but i am french.

I am interested in the Aquastream XT, but i have some questions :

the Advanced version have this fonction in more that the standard version :

Manually configurable fan output

What is it ?
It permits to connect a fan to the pump and to regulate this with Aquasuite ? Or it permits to connect the pump to a rheobus and to regulate Aquastream manually ; or to connect the pump to the motherboard and to regulate Aquastream with SpeedFan for example ?

Tank you. :)

cuto8

Full Member

Posts: 544

RE: Regulate manually the Aquastream XT

Thursday, February 19th 2009, 4:26pm

Quoted from "HollowMac"

Excuse me if my english is bad, but i am french.

Ça ne fait rien - mon francais est sûrement plus terrible ;-)

Quoted from "HollowMac"

Manually configurable fan output
What is it ?
It permits to connect a fan to the pump and to regulate this with Aquasuite?

It even allows to connect more than one fan, when using an Y-adaptor. You can also let the Aquastream/-suite controll the fanspeed automaticly!

HollowMac

Newbie

Posts: 4

Thursday, February 19th 2009, 4:40pm

Ok. Thanks. ;)

The Ultra version permits to regulate the speed of Aquastream with an externaltemperature sensor ; but if i use a sensor for my CPU, it's not very precise. It's better to use the internal sensor of CPU and to get back it with a soft. It is pity that Aquasuite doesn't permit to get back this and regulates the pump. Unless I make a mistake ?

:)

cuto8

Full Member

Posts: 544

Thursday, February 19th 2009, 5:00pm

Quoted from "HollowMac"

Ok. Thanks. ;)

The Ultra version permits to regulate the speed of Aquastream with an externaltemperature sensor ; but if i use a sensor for my CPU, it's not very precise. It's better to use the internal sensor of CPU and to get back it with a soft. It is pity that Aquasuite doesn't permit to get back this and regulates the pump. Unless I make a mistake ?

:)

First of all you should remember that the ultra-version already has an internal temperature-sensor. And the actual idea behind the external sensor was rather not to use a sensor for the heat of your CPU. As the CPU may have a very high variation in temperature it also wouldn't really make sense as your fans would increase speed everytime you start a programm. You should better use this sensor.

HollowMac

Newbie

Posts: 4

Thursday, February 19th 2009, 9:35pm

Hum ok ; i understand now.

Thank you very mutch for your explanations :thumbup:

I have already a sensor, and I find that it is difficult to adjust something from the temperature of the water. I know the limits of temperatures of a CPU, but of the water ?(

This post has been edited 2 times, last edit by "HollowMac" (Feb 19th 2009, 9:39pm)

Papa_Schlumpf

God

Posts: 5,009

Friday, February 20th 2009, 3:16pm

Well... Limit...30~35C° is a good temperature. :thumbup:
M.-Sys: Gigabyte GA-FX-58-extreme / 920@4Ghz / 6gig Corsair / 4870x2 all AC-B ;(



Wäre es nicht adäquat, den Usus heterogener Termini zu minimieren?
(Sollte man nicht weniger Fremdworte verwenden?)
8| ... 8| ... :huh: ... :huh: ... :wacko: ... :wacko: = :pinch:

Religionskriege sind Konflikte zwischen erwachsenen Menschen, bei denen es darum geht, wer den cooleren, imaginaeren Freund hat

HollowMac

Newbie

Posts: 4

Sunday, March 1st 2009, 11:03pm

Eventually, i took a standard version 8)

But, i have another question : what means "deaeration mode" ? The fact of removing air bubbles, or the fact to purge ?

Thanks.

Shoggy

Sven - Admin

Posts: 16,089

Sunday, March 1st 2009, 11:18pm

In deaeration mode the pump continuously starts and stops. In the starting phase there is a small twitch which can move unwanted air bubbles. So if you run it a few minutes you will get rid of the most air in the loop.

Similar threads