Suchergebnisse
Suchergebnisse 1-50 von insgesamt 275.
OK thanks for your feedback egawrangler
Or maybe the pump gets hot therefore it actually heats up the water by 3 degrees :-[
Seriously it's not too hard to say: this is a known problem, or something along these lines.
maybe they will like me more and answer it hehe
Hi, next week I will begin my rant over my aquaero (with a video showing the amount of problems I have with this software/hardware). But today I have a 'smaller' problem, my loop goes like this: Res-> pump (xt ultra) -> cpu ram etc -> water temp sensor -> rad -> res Now the pump displays the temp of the water if I'm not mistaken? In which it states it being 25,9 degrees C. The water temp sensor that I put in 'manually' (aqua computer parts), states the water temp is 22,9 degrees C. Now the water...
4 raptors... kind of a set back in terms of noise?
Hi when I try and place an order through aqua-computer.de using paypal. When i am forwarded to paypal to pay it comes up with an error in German. Saying something like 'error please try again'. Is this just my account or is it happening to everyone... it's been the same for the past 1 month maybe more. Ed
It's good...but quite the lazy mans case (can't be assed to fit the watercooling into a smaller space).
Should I contact support or just wait here?
Hi I have many problems with my aquaero/aqua suite and I am getting fed up!! 1) I don't even have a water level dector but yet on the aquaero it says "Shut down in (then a count down)" "Level too low"... 2) The aquaero lettering is proper messed up on both ends (kind of like ghosting/letters over letters etc.) 3) I open up the aquasuite and I get this message: Exception: InvalidArgument= Value of 266 is not valid for SelectIndex etc etc.... 4) When aquasuite does show up the aquastream XT tab ra...
I have had the same problem but it is too much effect to take the whole computer apart just for this problem... it is very annoying however!!
don't worry...sorted it... with superglue (I wasn't orginally going to use it because it might melt it...but this particular glue I found in tesco's could be used on rubber and it has seemed to have done the trick Ed
anyone?...please sorry but I am desperate.
The aquabox 5 1/4" black.
Hi I have been having leaking problems on the new res. but I think this is 100% down to the fact that the rubber seal that you provide is nearly IMPOSSIBLE to get on. Are you supposed to glue it on? Or something like this because otherwise you use all the fingers you have on 2 hands to fix it down....let go and the seal just pops off... Please help me Thanks Ed
hehe ok thanks yer it is a bit confusing...red flashing normally means high danger lol. Ed
Sorry - one more question. I am filling the system and the aquastream has a flashing red light...what does this mean? trouble? Ed
ok thank you for your answers
I did not get a manual with mine German or English...but this doesn't really bother me...I just want to know if the connectors called "fan" and "rpm" and "ext.temp" need a lead to go into something or not (in order to get everything out of the aquastream XT) Thanks Ed ps I am still setting everything up this is why I havn't looked for myself in Aquasuite to see if everything is working.
ok so use both. Anything else I need to connect to get the features of....my setup: aquastream xt several blocks 360 xt the new aquacomputer flowsensor sorry...I am only asking because there are quite a few connectors on the back of the aquastream xt and it doesn't come with a manual. Thank you again Ed
ok thanks.... and am I right in thinking I then don't have to connect it via USB..(to the motherboard) - sorry just want to make sure I get everything right 100% Ed
ok thank you for your quick answer But how about the aquaero, is this connected to the aquastream XT?
Hi I just bought the aquastream XT - while I used to have the aquastream with the flate plate (e.g. with the 2 led lights etc.) Now do I have to use this front plate with the new aquatream XT or shouldn't I use it at all or is it optional? Thanks Ed
I didn't quite understand what you meant...the controller is connected directly to my psu....Unless you meant connect the pump straight to the psu?? But im not sure how to do that... The jumper settings are correct...I looked at the manual and they are the same as my settings on the pump. My aquaero is also having problems (the text isn't appearing properly on the display... double vision sort of thing). I'll get some pics of it soon if needed...maybe this is a sign that the aquaero maybe sent o...
Hi its totally dead.. there no noise no vibration. I've checked the cable, i've put it onto the aquaero and onto its own aquastream hardware board, both didn't work. Aquasuite and the front bezel says the aquastream is "OK" which is werid...Settings are as default. Thanks Ed
Hi I think my aquastream is broken...I have only had it for 1/2 months. It simply will not pump (no noise ...nothing) It was working fine 2 days ago...and now...nothing. Any ideas? Can I do something to make it work? To send it back....quite a big deal..I am at university and havn't got time to take apart my computer + I need it for homework! Thanks in advance Ed!
wherever you want... I would get the water temp conversion thingy so you can see how hot or cold the water is. Then you could have one just outside the case... one inside the case...one selotaped to a hard drive....just a few ideas..
any information on the size?.. smaller or larger than the current aquastream etc.?
I had the same problem with the Cuplex Pro CPU block, it hasn't happened with the XT block but I was advised a while ago that people in the german forum also has this problem (simply due to dirt on the block) so I cleaned mine (its harder than you think!), and everything was back to normal. Ed
Hi do you have the aquabox 3 1/2" in black?? If not...will it be made ;D Thanks Ed edit: and what does: Abstandshalter zur Montage von airplex PRO/XT (Set 4 Stück mit Schrauben) ...mean in english?
I had the same problem... as sniffer said.. its quite easy to believe you have... when you actually havn't
Hi do you sell a block to fit the 8600 gts? I noticed you have one to fit the 8600 gt, but I wasn't sure if it meant the gts aswell... Thanks Ed
thanks for the quick reply
Hi in the aqua computer shop you sell the tubing ... but is this price per meter or something else? Thanks Ed
I already have a lian li pc70... but its just too big for me! Keep suggestions/pictures coming in though...
I am going to start to re-build my computer and not use the 1800 rad i have (just toooo big) so instead i will use the 360 xt.... but which case should i use for it? I want to build it into the case like many people have ... is a middle tower going to be adequate? I was thinking of the lian li PC-V1200B Plus II or the PC-V1000B Plus II... does anyone know the difference? Hope i'm allowed to ask these questions in here Ed
I'm very interested..i've sent you a I.M Ed
Nice!! Can it out-perform the cuplex xt?
well not necessarily... if you have the time.. i would check the temps of when you have the sensor.. and when you don't have the sensor... if they are a big difference then scrap the sensor.. but in my honest opinion.. I don't think the flow makes that much of a difference (especially if you have aqua computer blocks). Ed
OK. i don't know the solution.. but why do you love x64? it really doesn't make any difference apart from the amount of ram you can have.... and when server boards are the only boards that allow you to have more... why anyway it doesn't make any performance differences.. only slower in most cases. nevermind.
have you installed NET framework 2.0 and why do you have xp64 anyway... its really not a good operating system - it doesn't have any advantages... only disadvantages
same as above...but you can't active it.. not disactive other problems... 1) on the fan tab the graph is labled in german.. but i am in english mode 2) setting the power output for the fans (at least for one of the fans i have tried...), if you set the value @ 99 or lower and press enter or click away to active it, the value will automattically go to a value of 1 lower... e.g. set it at 11% click away.. and the value will now be at 10%. 3) the timer.. aquaero time: the day is in german... not en...
Nice! Can't wait to hear these "interesting improvements"! Ed
But its not that difficult to see what you need... e.g. " 29.90EUR* twinplex pro SLI-Typ 1" hmmm ... costs 29.90 euros and the product is the twinplex pro sli-Type 1... Also to make matters easier there are pictures Good Luck Ed
Hmm yes I had this problem but I can't remeber what I did to get it to normal either... if I remeber I will post [I have a dfi sli dr by the way] Ed
Answer to the second question - Yes they do ship internationally.