• 09.12.2019, 01:51
  • Register
  • Login
  • You are not logged in.

 

Search results

Search results 1-22 of 22.

Thursday, April 17th 2014, 8:21am

Author: sylvainp

When Aquasuite software update will be release !

When the next software update for Aquasuite will be release ?

Saturday, January 25th 2014, 7:00am

Author: sylvainp

which flow sensor should i get?

I didn't RMA the MPS Flow because it will cost me around $30 CAN to send it to Germany. They don't have an America support office. This flow cost around $60 so it's not worth spending 50% of the actual cost to send it. If I add up the cost of the Flow sensor + Cost of shipping to get it repaired I'm well over $100 CAN Unreliable product for the premium price we pay for this.

Friday, January 24th 2014, 10:13am

Author: sylvainp

which flow sensor should i get?

Don't get the MPS flow because they don't last and quite some people have leaking problem around the electronic board. I didn't have the leaking problem but mine stop giving me Flow data after only a few months (max 5 months)

Friday, January 24th 2014, 10:08am

Author: sylvainp

MPS Flow 400 - No flow reading

Well as for great support and great products I will pas on this one... It took more than 2 weeks for Aquacomputer to test my D5 pump before they decide to send me a new one (mine was not even 2 weeks of uses) And now the MPS flow is broken. I live in Canada and it will cost me about $30 to send it to Germany and this thing Worth around $60. I have it for less than 6 months and it's broken already. Some people have it to work for only one day ! And I don't talk about leaking problem too. For prod...

Saturday, January 11th 2014, 4:05pm

Author: sylvainp

MPS Flow 400 - No flow reading

I reconnect the USB cable. Even my 2 pumps at 100% I get no readings. Current Unscaled Value = Always stay to 0 No help from the staff of Aquacomputer in this forum ?

Saturday, January 4th 2014, 6:31pm

Author: sylvainp

MPS Flow 400 - No flow reading

Nop, factory reset already did this several times without success. The firmware kill it I think.

Saturday, January 4th 2014, 1:57am

Author: sylvainp

MPS Flow 400 - No flow reading

Quoted from "wa3pnt" 1. I also find that Aquasuite crashes when it first loads and I select MPS>Configuration. If I re-open Aquasuite, I can then access MPS>Configuration. I have reported this elsewhere on the forum. 2.It sounds as if your MPS configuration is not loaded, and/or you have to update the firmware on the MPS. If you are using Aquasuite 2013_5.2, and select MPS>Settings it should prompt you to update the firmware. Then it should work properly. RodeoGeorge I Already update the firmwa...

Friday, January 3rd 2014, 11:07pm

Author: sylvainp

MPS Flow 400 - No flow reading

I just update the firmware of the D5 pumps and the MPS flow 400. Now I dont have flow reading from the MPS flow 400. I do have the water temp and the signal output send RPM to the CPU fan header in the BIOS. Sometimes I have some spikes of flow readings but very rarely. I connect the USB cable and did a factory reset. Then I put ba ck priority to Aquabus and channel 14 because I have 2 D5 pumps which use channel 12 & 13 In the configuration where I select the flow meter and size of tubing I dont...

Friday, January 3rd 2014, 7:28pm

Author: sylvainp

AQ 5 Pro (firmware 1034) Bug - Random AQ 5 Pro Resets

I have the same issue as you have. Now my MPS flow 400 don't work anymore and don't give me flow rate anymore. I have plug the RPM signal to the motherboard CPU and in the BIOS I have a RPM on the CPU fan header. Even if I use the USB cable on the MPS Flow 400 as soon I select the MPS - Configuration then Aquasuite crash and I need to restart Aquasuite and after I can configure the MPS flow. I update to firmware 1008 and since no more flow rate. Under the graphic I dont have uncalibrated values ...

Sunday, December 8th 2013, 11:39pm

Author: sylvainp

Defective pump send to Aquacomputer = No status

I have send my Noisy D5 pump USB to Aquacomputer and I want to know what happened with the pump ? I had a reply in my email on the 27th of november that they were goinf to test it. Never had any status for the replacement since then. I will appreciated as a Aquacomputer Customer to have feedback and service. I need this pump. Thank you

Saturday, November 2nd 2013, 6:40am

Author: sylvainp

RE: High flow meter usb not working after one day

Quoted from "delevic" Hi, I have aquacomputer high flow meter usb. After a day of work, I stopped to get flow-information. I also noticed irregularities in the readings of water temperature. It is quite slow to react to changes and gave the incorrect temperature +-1.2c. I compared with three thermometers ..... I reinstalled netframework 4.5.1 , and aquasuite... What to do ? Best Regards Delevic Go in the sensor pages and select the Flow sensor temp and look on the right you can make a temp offs...

Saturday, November 2nd 2013, 6:37am

Author: sylvainp

aquasuite cpu?

Maybe the new version of Aquasuite will read CPU, motherboard, etc. But at the moment you need Open hardware Monitor or Aida 64 The new version of Aquasuite was supposed to be release this month but we still waiting for it.

Friday, July 5th 2013, 4:36pm

Author: sylvainp

Aquasuite - Here are my settings - What are yours ?

Well This weekend I finish testing my loop outside my PC and I installed everything Inside. (still waiting for my GPU block) So for now I use a 360 rad to cool the i3770K and the Asus motherboard Fusion Block only With both D5 (serial) at full 12v I get 1.6 Gal/min ( seem a bit low for 2 pumps) As for water temp my rad In/Out are almost always the same temp (I installed the temp sensors on the RAD port) The MPS sensor temp is always a bit higher So to control my RAD fan I also use the water vs a...

Tuesday, July 2nd 2013, 6:56pm

Author: sylvainp

Aquasuite - Here are my settings - What are yours ?

Thanks I figure it out. I was playing with the chart settings in Aquaero and I jst find this is for the front panel to display chart. i'm playing with the chart right now.

Tuesday, July 2nd 2013, 6:40pm

Author: sylvainp

Aquasuite - Here are my settings - What are yours ?

How do you make these graph ? i could not figure it out so far. Thanks

Sunday, June 30th 2013, 7:06pm

Author: sylvainp

Aquasuite - Here are my settings - What are yours ?

I have a question: How do you think the all in one CPU cooler (Corsair H100i and others) are working to control the speed of fans on the radiator ? For me I think it is based on the temp of the water. "The Air/water delta will always change, while the rad in/out can change briefly with the warmed water hitting the first sensor but once the water goes all the way through the rad the delta drops again, the load is still there but the delta is not. " The water coming from the CPU, GPU will always b...

Saturday, June 29th 2013, 9:51pm

Author: sylvainp

No flow reading from MPS Flow

Figure it out. You need to use the USB wire first and configure the MPS Flow Then you need to select the Flow sensor and also the size of fitting used then you import the data. I also set the Aquabus as the priority port. All done With the 2 x D5 (in serial) at 3300 RPM I get 5.3 L/min If I control the pump speed with the PA2 the amplifier easily get to 70 degree. I find a sweet spot at 3300 RPM for both pumps. To get less heat produce by the PA2 I set them to 12V (100% power) and use the Dial o...

Saturday, June 29th 2013, 9:36pm

Author: sylvainp

Aquasuite - Here are my settings - What are yours ?

Thanks to reply with a good explanation. That Exactly why I use the RAD in and RAD out water temp to create a Delta T to control Radiator fan speed because the water temp change is pretty fast Under load. Cooler water = Cooler CPU & GPU temp It's also a good way to find the sweet spot for the fan RPM (low and High) You get to a point that fan RPM does not change the water temp as much. So I use the Delta T of the radiator IN/Out as a reference to control my Radiator fan RPM (Low & High) and also...

Saturday, June 29th 2013, 6:55pm

Author: sylvainp

No flow reading from MPS Flow

I have a AQ5 and 2 x PA2 I have no flow readings from the MPS Flow (400). It's wired using the Aquabus cable, From the sensor I have Water temp reading from the MPS. In the flow settings I have multiple Flow Flow 1 Flow 2 Flow 4 Flow 11 And they are all at 0 Is the sensor faulty or i'm missing something here ? Thanks

Thursday, June 27th 2013, 6:21pm

Author: sylvainp

CPU Fans header RPM signal

I would like to know which output I use to send RPM signal to the motherboard CPU header. If something happen (pump failure, CPU temp) I want the PC to shutdown. I also have a MPS flow and I think the RPM can be use with a 3 pin fan cable but i'm not sure. Thanks

Thursday, June 27th 2013, 5:52pm

Author: sylvainp

Aquasuite - Here are my settings - What are yours ?

I'm new to WC and also Aquacomputer. I was playing with Aquasuite 2013 and I test the unit and program prior to make the Watercooling in the PC. I plug all the fans, Temp sensor, Water temp sensor, MPS flow Here what I will do in my WC setup --------- AQ5 Pro 2x PA2 (using Aquabus) 2 x water temp sensor on the reservoir (input and output) 3 x case internal temp (Intake, Ambiant, Exhaust) 1 x MPS Flow 400 Dual bay reservoir 1 x EX 360 radiator 1 x CPU 1 x GPU 680 Asus Onboard Fusion block Aquasui...

Friday, June 21st 2013, 5:31am

Author: sylvainp

New user - Need help

Hi all, I just got these from Aquacomputer Aquaero 5 Pro 2 x Power Adjust 2 1 x MPS High flow sensor (400 model) I have read that I need to change the Power Adjust 2 ID prior to plug it on the Aquaero 5 which I did. I plug the power and the USB to the first PA 2 en after I start Aquasuite 2013 and I see the PA2 and the ID was at 50 so I let it this way. Unplug the first PA2 and connect the second PA2 with power and USB Windows says their is a problem with the USB device and in Aquasuite I have a...