• 22.05.2018, 15:23
  • Registrieren
  • Anmelden
  • Sie sind nicht angemeldet.

 

Suchergebnisse

Suchergebnisse 1-15 von insgesamt 15.

Sonntag, 15. April 2018, 22:00

Forenbeitrag von: »zerophase«

Anyway to add additional pwm headers?

Oh really. Didn't realize that feature was added. Guess I'll be picking up an LT. Would still be ideal if a new poweradjust with PWM support comes out.

Sonntag, 15. April 2018, 02:15

Forenbeitrag von: »zerophase«

Anyway to add additional pwm headers?

Currently, I have all 4 pwm headers occupied. Two for the radiator fans, one for the case fans, and one for my pumps. Whenever NVidia comes out with their new graphics cards I'll be moving to a dual loop system. So in total I'll need five pwm headers to control everything separately. From my understanding I could slave another Aquaero, but won't be able to use pwm control for that. Is there a solution available for adding more pwms?

Sonntag, 8. April 2018, 05:21

Forenbeitrag von: »zerophase«

Using temp sensor connected to mps flow 400 with aquaero controller.

Hey I'm just checking if it's possible to use a temp sensor connected to the mps flow 400 with a fan controller on the Aquaero 6? I can't seem to find that temp sensor in the list of inputs

Freitag, 23. März 2018, 21:17

Forenbeitrag von: »zerophase«

mps flow 400 to diffuse or not to diffuse?

5 cm before and after the mps flow 400 I have EK fittings with 9 and 10 mm inner diameters. The rest of the loop is 13/19mm tubes. Would it be appropriate to use the diffuser plate with this setup? Would the unit stop reading accurately faster when using it with pastel coolant? By the way are there any calibration curves online for other fittings and tubes?

Freitag, 23. März 2018, 18:10

Forenbeitrag von: »zerophase«

Does AQ 5 / 6 screen replacement fit XT?

Zitat von »Shoggy« No, this is an optional display cover for the aquaero 5/6 PRO. What is damaged? Just the cover or the display itself? Both are not available in the webshop but you can get them as spare part by sending an e-mail. Just the cover is damaged. The front of my Enthoo Primo popped off while draining the loop, damaging the cover in the process.

Freitag, 23. März 2018, 04:59

Forenbeitrag von: »zerophase«

Does AQ 5 / 6 screen replacement fit XT?

I damaged the screen awhile back taking a gouge out of the screen. Would this fit the XT? https://shop.aquacomputer.de/product_inf…roducts_id=3154

Freitag, 23. März 2018, 04:56

Forenbeitrag von: »zerophase«

How am I supposed to connect the power connect to the Aquaero 6 xt?

I have one of the three pin relays and a power connect. Do I just cut the green wire, and attach it to the the relay? I'm guessing I will need a soldering iron. I'm also guessing I want to attach the 2 pin header to the motherboard. So, I also have a Silverstone remote with power and reset passthrough for turning the computer on, is there anyway to hook the PC case, AQ / AQ remote, and Silverstone remote up at once?

Sonntag, 4. März 2018, 15:32

Forenbeitrag von: »zerophase«

Aquaero with dual loop system

Might as well piggyback on this. I'm going to be doing something similar in a few months, and wanted to check if it's possible to get more than 4 pwm headers running in pwm mode. (2 pwm headers for each loop's fans, 2 for the pumps, and 1 for the case fans) Definitely need at least five headers, maybe more depending on the final build. In response to mpowerh, The low port is disabled in the latest firmware. You can just chain all of the aquabus devices together on the high port. I use an mps 400...

Sonntag, 4. März 2018, 15:09

Forenbeitrag von: »zerophase«

MPS 400 reporting flow rate of 0.

I recently flushed the system, so it might start working. That being said I'm still going to get a replacement just so I don't need to drain the loop in case the thing is dead. Going to run it through some Mayhems Blitz part 2. Is there anyway to mock test the device? Just to verify if it still works, without placing it in the loop. Overall, it took two years for the pastel coolant to kill the device. I'll still be using pastels in the future with it.

Sonntag, 4. März 2018, 02:29

Forenbeitrag von: »zerophase«

Will laying mps flow 400 on the bottom of the case cause any issues?

Previously I had my mps flow 400 suspended off the case bottom between a few fittings. Currently I'm in the process of removing some fittings for soft tubing; so, I'll be laying the sensor on the case bottom with the 1/2in. ID X 3/4in. OD tubing coming before and after for the required run length. Will there be any issues with just having the sensor laying on the floor of the case? (lowered accuracy, increased noise, increased leak risk, etc Also can I just plug the temperature sensor into the m...

Sonntag, 4. März 2018, 02:22

Forenbeitrag von: »zerophase«

MPS 400 reporting flow rate of 0.

Looks like it was an issue with pastel coolant clogging the sensor

Samstag, 16. Dezember 2017, 09:45

Forenbeitrag von: »zerophase«

Isn't pure copper more thermal-conductive than .925 silver?

Copper is why the statue of liberty is green. Diamond would work, but too bad one company controls the world's supply.

Samstag, 16. Dezember 2017, 01:02

Forenbeitrag von: »zerophase«

MPS 400 reporting flow rate of 0.

The MPS only shows a license for 2016. It looks like the issue can be fixed by reinstalling 2016, but I can't find that download anywhere. By the way, the configuration screen for the MPS 400 appears to have changed at some point during the 2017 release. Also if I drop the pump down from 3900 rpm to 1200 rpm, and click set current flow to 0 I start getting a current unscaled value of about 8, under the mps 400 calibration curve. Feels like automatic calibration isn't running when I put the shutd...

Samstag, 16. Dezember 2017, 00:41

Forenbeitrag von: »zerophase«

MPS 400 reporting flow rate of 0.

I just noticed that my MPS 400 has stopped reporting a flow rate of any kind. I currently have it connected to through a usb and aquaero header. I've tried playing around with zeroing out the meter during standby, and have had no luck. I've had the meter for about 2 and a half years. Is there anyway to get the meter reporting flow again, or is it dead? Where can I find default calibrations to reset it to factor settings?

Montag, 12. Dezember 2016, 20:17

Forenbeitrag von: »zerophase«

Aquasuite 2017

I just did the upgrade to 2017-1.3 from 2016, while retaining old settings. I can see my gauges on the desktop, but it's in liters per hour, everything is maxed, and I can't get the Aquasuite menu to open for adjusting settings. Update: Alright I shutdown for a few hours and tried getting the tray icon to open again. This time it opens fine. If you want any logs I can send those to you. I'm guessing it is an intermittent problem.