Suchergebnisse
Suchergebnisse 1-31 von insgesamt 31.
No, the flow rate seems to work just fine and like it always has...currently it's approx 80 l / hour. This isn't really a big deal since I also see the water level on the side of the aquaduct (the little floating ball) but of course it would be nice to also have the correct value in the display.
Hi, A couple of weeks ago I replaced my graphics card and at the same time I cleaned my water loop and filled up water but for some reason the last couple of days I've noticed the displayed water level is medium even though the actual water level is high. I've tried setting 100% level reference in the software and then after a new measurement is performed the level is correctly indicated as high again but then after a couple of days it report medium. How come is this and is there any other way I...
Have someone in here already tried the new aquagrafx 480 water block on msi's N480GTX M2D15 card or can someone confirm it works? I'm thinking of buying this combo but just want to make sure I don't end up with a mix that for some reason doesn't work but as I understood it msi is following Nvidias reference design and that in turn should garantee that the aquagrafx water block will fit on the msi, correct...? Thanks in advance for your advice!
Thanks for your prompt reply and explanation! Since having it on automatic makes the aquaduct a bit noisy I think I'll stick with having that option unchecked since I also did a temp test which in fact showed me that having a flow rate of approx 75l/h gives better cooling performance in my situation over the automatic mode which results in a flow rate of approx 95l/h. I belive I've asked this before but is there an English manual for the aquasuite I could download somewhere describing all differ...
Hi, Could someone please let me know the recommended pump settings in aquasuite (4.66.00) for an aquaduct 360 xt mark III and also, what would be considered as a good flow rate when cooling a Core i7-920 @ 3.8 GHz and a GTX285 graphics card @ stock speed? Looking under the Pump tab in aquasuite I would like to know how to use Automatick frequency settings and Minimum pump frequency. By default the Automatic frequency settings is unchecked giving me a flow value of approx 75l/h and the Minimum pu...
Got the answers to my questions by running the fan wizard which contained some valuable information, however I still think it would be great if you could come up with some documentation for the aquasuite software - I'm sure we are many that would appreciate that.
Thanks for the tip, under the fan tab it's set to 'Regulate fan via highest value from...Water out' and this is the default setting. I guess the Reference value doens't work the way I thought, ie that the Reference value is the temp the aquaduct will try to hold at all times. Maybe Shoggy can tune in here...?
Shoggy, Can you please explain the Reference value to me? I though that is the value (temp) you ask the aquaduct to try to hold at all times meaning the fans if set to adjust to temp would spin faster and faster until they manage to reach the temp set as the Reference value but...I have now the Ref val set to 35 C and running Prime95 the water out temp is 38,5 C and still the fans only spin at approx 20% - why don't they increase their RPM to decrease the temp to the value of 35 C I've set in th...
Hi again, You can forget about my first question about the LEDs and the min/max values, just realized how to use them and set an interval that will give me the feedback from the LEDs I like to have.
I guessed it's the sensor settings I should adjust but I don't 100% understand how to use the min/max settings...what they actually mean? I did try to change those values but I couldn't notice any difference looking at the LEDs regardless what values I put in there. Other things in the software I would appreciate if you could explain are: - Override mode active - Reference value - Hysteresis in K - Automatic frequency settings and Minimum pump frequency (the latter is checked by default while th...
Hi, Trying to figure out how everything works in aquasuite without any doc is there any way you can adjust at what temp the LEDs turn brighter/darker? In my case I find the red LED light to get too bright too fast (even when I don't have any alarming hot temps).
I add to what TopNurse says, would be great with a manual since the software really is amazing with all different settings and tuning possibilities and feels sad you might miss out of great functionality simply because you're not sure how to make best use of the software.
Worked great, thanks! Am I right that depending on what language you've set in aquasuite at the time you flash the firmware decides what language you will have after flashing the firmware? Another question on documentation, where can I find an English version for the aquasuite software?
Thanks for your prompt reply Shoggy! As for the firmware, could you please tell me the exact name of the firmware I should use to get the latest version for my mark III 360 and also English language in the LCD display? As for the water direction I can now after changing tubing confirm that on my unit the outer nozzle is water out and the inner nozzle is water in. Might be me just beeing stupid but I find the engraving a bit confusing, would have been great to simply have the words IN and OUT ins...
Hi, After having lots of problems with my 240 PRO I decided to replace it with a 360 XT Mark III and now I have a couple of questions. 1. Is it possible to change the language in the LCD display to English? 2. Noticed there is an option in the software to upgrade the firmware both for the unit itself and also for the pump, should I consider that or is it just if you have problems you should upgrade the firmware? Also there seem to be different firware upgrades, both in English and in German - is...
Not sure what an Aquaero is but if you mean a LCD display of some kind, no it doesn't have that. However I after posting my first post dared to boot all the way into Windows after my CPU had cooled down. Reason I wanted to do this was to check what the Aquasuite software would say but it didn't even find my device anymore so I guess that pretty much says it all...my Aquaduct device for some strange reason is totally dead so now I'm waiting for a response from aquacomputer support how to solve th...
Hi, Today when I started my computer my Aquaduct 240 PRO didn't start with the computer as it usually does, the pump nor the fans are running and I'm only lucky I noticed this right away so I didn't boil my computer. Any idea what might have happened and how and if I could possibly fix it? I really hope I don't have to send in the unit for repair because I use my computer every day. I have verified I have current at the end of the 15-pin power cable that goes into the Aquaduct so I guess whateve...
Don't know the history behind it but thanks for the link to that forum, lots of good stuff but parts of it seemed a bit old though.
Thanks for answering but I also posted this question over at overclockers and there I got the answer that it was OK to flush the system with tap water as long as you then rinse it with distilled water afterwards so that's what I've done now and I'm just finishing up cleaning my waterblocks as well both the CPU block and the VGA block. So...all that is left now is to put them into my PC and then I hope all will be good this time!!
Hi, After having some problems which might have been caused by using too much of the AC Fluid that comes with the aquaduct I would like to clean my system and my question now is - is it OK to use tap water for this or must you never ever have any tap water inside the system? Of course I will then when installing the system use distilled water again but would be much easier to be able to use tap water for the cleaning purpose. Thanks in advance, Richard
Thanks alot for your answer and for the link to that other post, seem to hold a great lot of info and especially when you like me don't speak German and don't have any documentation in English or even better yet Swedish in my case One thing I notcied in that other post is there should come a CD with the product holding both German and English documentation as well as software but I never got any CD with my 240 but maybe the CD is only included in the 360 or was the CD missing in my product? Anot...
OK, thanks guys - I'll have another look and will also do some testing.
Thanks alot, I'll try that! What exactly is this mode you're talking about, how does it work? Also, when you say this can create all kinds of problem what are those problems...should I be worried I have broke anything in my new 240 PRO system ? I've already said it but I say it again, I'm very surprised in a bad way you don't get an English hardware and installation guide with the system when you buy it so you can avoid all these kind of "mishaps" when you're not German.
Thanks for the link, I'll check it out. As for the waterblock I'm 99% sure there isn't any wording on mine but I'll have a second look.
Might already have seen the video but please send the link, thanks! Might be a combination English isn't my native language in combo with beeing a rookie when it comes to watercooling but what exactly is meant with "bleeding"? To me it would make sense having the "water in" above to help the water fall down and then go out from the waterblock again instead of having the pump "push" the water upwards through the block? Also what port should be used for "water in" and "water out" on the cuplex xt ...
Hi, When installing the waterblock mentioned above how should it be oriented for best results, should the 'water in' be above or below 'water out' and also, what port on the block is 'water in' and 'water out'? Isn't there any documentation when you buy this block or was it just missing in my product? Thanks in advance, Richard
Managed to set the system up yesterday by guessing and with some help from Google Translate...however I have one question. I used distilled water and then added some of the ACfluid that came with the product but I might have added too much because now after running the system for about one day the water is almost white like milk and I also seem to have lots of air in the loop and not sure how to avoid that or how to get rid of it when it's already in there...? Thanks in advance for any advice!
I'm happy to tell you the system is now up and running and I didn't have any problems connecting it via USB and it showed up just fine within the software on the first try! So for anyone else wondering it seems the problem has been fixed, maybe in a BIOS upgrade from ASUS.
Zitat von »djbergwerk« Hi, ecb123 I have the same Issue like you. There are some Problems with the Aquaero and some USB Devices, specially on Asus Boards. You can try and install a internal USB PCI Card with a internal USB Header and than connect your Aquaero to this. It´s not a Problem because your OS, I personally run a Asus P6T Deluxe, Vista x64... I just bought and got a new 240 system and I also have an ASUS P6T Deluxe running Vista 64bit, are you saying you got this work by connecting the...
Thanks for the promt reply and the links! As for the software I found that menu option so that is great. About the tutorial it was good but I'm afraid I maybe missed some important information (for example they were talking about the importance of checking some jumper settings?) and also the tutorial was for the 360 system and not the 240 I have but maybe that doesn't matter? As for the manual that seems to be mainly for the software (correct me if I'm wrong) and not the hardware, what I would l...
Hi, Today I got my aquaduct 240 Pro Mark II but noticed there is only documentation in German included, where do I find the English documentation for my new system and same question goes for the software - where do I find the latest English version for download? Then my last question, I read a post in here it might be a problem having the system recognized in 64 bit Vista when using ASUS motherboards, is this a known problem and if yes - is there anything beeing done to correct this? Thanks in a...
06.05.2024, 03:11
Sprache ändern
Registrieren
Anmelden
