Suchergebnisse
Suchergebnisse 1-50 von insgesamt 177.
Zitat von »sebastian« Try to update the lastest intel mainboard driver. Try with the default system clock, do not overclock any hardware. Close/uninstall all software from Logitech or Razor input devices. Ensure every device driver and software is up to date. Windows 10 has in the current state many issues. I think in 3..6 month the situation is better. Thanks I'll see if Asus have a windows 10 driver set yet first and then try an intel set.
Zitat von »Shoggy« @Phatboy69: was it working before? - Because this sounds more like a general problem with the USB communication and nothing related to Windows or the aquasuite software. Hi yes it was working perfectly before the upgrade from win 8.1 x64 to win 10.
Hi Shogmeister I am having windows 10 issues too. (Aquasuite 2015-6) I've tried upgrade and clean installs and the aquasuite seems to loose communication after a few seconds of booting into windows. I've tried a difference internal port, unplugging all USB devices and plugging in a basic USB and mouse and I still loose USB connectivity. I can change values on the controllers and fans will increase and decrease but the values are not updated in Aquasuite. I get aquasuite lock ups and crashes too ...
Zitat von »Jeremy« Did you run it full speed or reduced? How long did it last for you? I have a curve controller set with a minimum voltage of about 8.2v when system is under light load and water temps are stable but it does spin up to 12v when the system is under high load. I turned fan controller voltage to zero and back to full voltage in Aquasuite and the pump has restarted but it seems to fluctuate and eventually shut off if I put it back to the automatic curve controller i have setup. The...
Thank god for Pump redundancy and Aquacomputer Aquasuite monitoring on the G19! I should point out its not an AC D5 just a laing D5.
Zitat von »Jakusonfire« The USB D5 pumps aren't voltage controlled anyway. They have an internal motor controller just like the D5 Vario, that has a set minimum speed of 1800RPM that equates to the 25% power setting in Aquasuite. I have the vario D5s and they voltage control just fine with them set on 5. They just dont spin as slow as when using the built in 5 settings on the control switch.
Zitat von »Jeremy« 25% of total available volts isn't the same as "25% speed", technically. Every DC powered device, be it a fan or pump, has two important voltages to keep in mind: 1. Minimum starting voltage. This is the voltage required to get the thing spinning from a dead stop. My Yate Loon fans have a minimum starting voltage of around 3.6 volts, for example. 2. Minimum operating voltage. This is the minimum voltage that can be applied to a device and still have it function (spin). My Yat...
Zitat von »MossyRock« Arad85, Thank you very much for this information! It certainly helps me understand the integration process. Without digging too much, it looks like Aida64 reports voltages also, but you're saying that Aquasuite either can't reference them or ignores them? If it can/does reference them, I would assume a 12v voltage value would be interpreted by Aquasuite as 12 degrees? If that's the case, that would be fine because I would know how to interpret it. Even if the controlling o...
Zitat von »WCDummkopf« Hello, I am working on a new build and trying to resolve a compatibility question before I waste some money. After not hearing good things about Corsair Link, I have ordered an Aquero 5 monitoring system. However, I am happy with my current Corsair PSU and was looking to get the AX1200i. It comes with a 4 pin connector intended to go to the MoBo via a USB dongle and an internal USB connection. Can this go direct to the Aquero 5 via an aquabus, or can I access the controls...
Zitat von »xvs87« Awesome, does it have to be wired into the Mobo or can I use any usb port that is connected to the computer? Its designed for internal MB USB port headers but I guess you could use an adapter that would convert external USB to internal header if you dont have enough internal ports? Something like this.. http://www.scorptec.com.au/computer/47189-c-rausb3002-in
You can run both AQ 5 XT off seperate internal USB ports and have full functionality of all sensors and controllers and Aquasuite will treat them as independant controllers no problem!
Here's my datamap files and G19 layout for those that want to see how its put together.. I added temp bars to CPU cores, GPUs and water and edited some icons and imagemap files. I now get orange indicators for when pumps, fans or flowrate are at maximum, and triangle warning when low or exclamation alert when below minimum. Temp alerts are the opposite going from low to exclamation alert. I run my datamap files and XML from the C: root directory. The eos-19 Layout from the layout folder using my...
My machine only use 4-7%... not sure what an older system like yours would use or whether there is something else going on.
I didnt change anything else. I suggest checking the format of your map files and make sure all data fields are seperated by a tab and that there are no erroneous spaces. From memory your imageviewer widget was returning the correct value from the datamap but the imagemap wasnt returning the correct image. I would also make sure all paths and directories are correct.
Pump datamap Quellcode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 [Format] type=xml ; xml / txt / ini dataExpiry=0 ; # of seconds to consider the data invalid language=EN ; The language used by the lists in this file. Other languages can be added by copying the lists to a new text file, ; translating them and then saving the file as "lists.<language>.txt", e.g. lists.RU.txt [List:TempStatuses] ; ...
This is whats possible! I made a status screen for my G19 keyboard colour screen that uses Aquasuite XML export and LCDHost to display the data from Aquasuite! There's a XML Export thread in the english forum that details my long journey to get XML export working.
Looks like it should work to me.. Save the layout and reload it or shut LCDHost down and restart. I noticed I had to do that in between changes to make the status icons show up.
I got my status screen finished!
You need to add the same list:TempStatuses,1 and list:TempStatuses,2 to the lines in the datamap file for your external sensor and fan rpm and also the [List:TempStatuses] section at the top of each datamap file.
Not sure what your problem is.... Its picking up the right value for logdata.LogDataSets.CpuTemp.Level.Code logdata.LogDataSet.value list:TempStatuses,1 The value is working in the lookup table. Maybe check you have tab delimted the columns in the [List:TempStatuses] section and in your imagemap file also make sure the columns are tab delimited. (ie delete the space between each value on each row and the press tab between each value to create the delimit) Also make sure you have the right paths ...
This [List:TempStatuses] section and the 2 entries list:TempStatuses,2 & list:TempStatuses,1 need to be put into the datamap file your already using to collect Aquasuite sensor data. These sections are new to enable the lookup of status codes. Here is my datamap file with the changes I made to enable the lookup table. (list) Quellcode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 [For...
Just use this imagemap file as is. dont change it and everything should just work! Quellcode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ; The image map file instructs the SpeedFan Status Image on what image ; file should be displayed for what circumstance. The images listed ; need to be in the same folder. ; ; The format is as follows: ; <Code> <Image File> ; Note that each item is seperated by a tab. ; ; You can miss out any of the codes below and the Status Image will ; try to adapt sensi...
You dont need to put the list temp data into the imagemap file.. the default file should work but you may need to add a missing shortcode in the imagemap. Just checked there is nothing missing in your imagemap but you need to delete the list data section incuding [Format] and below.
Maybe restart LCDHost or check your image map file. Make sure the short codes in your imagemap match the shortcodes in the datamap list.
Almost finished my new status page.
Zitat von »novax1« hello you changed. Status Icons / Silk 14x14/imagemap.txt? can set an example. please thanks The imagemap uses the short codes here to choose which image to render. In the datamap file I have added a 3 column lookup table (list) which tells the imagemap which sensor value to lookup the shortcode for. [List:TempStatuses] is the lookup table where each tab delimited entry is; column 0, numeric value of the sensor which determines which short code (column 1) and caption (column ...
Zitat von »AE5probigNGslave« Zitat von »Namron« Have a lookHERE & it may help you out N. It is not useful for me.I already read temperature sensors from OHM in aquasuite, but I need read RPM from bigNG through OHM. Any idea? There's currently no way to do this. You should replace the bigNG with Poweradjusts or an Aquaero. Aquasuite Software sensors only work with temperature.
Set alarms with temperature, flow or pump rpm alerts. Set a warning and alarm. I have mine set to give warning if maximum temp is reached and if temp keeps rising it shuts down. I also set warning and apply full power for low flow rate. Then set actions for the alarm level.
New Work in progress.. Im making a new Overview / Status page and I finally worked out how to make imagemap files for images! So I can set icons for status of water/fan/pump status!
You need to setup alarms in Aquasuite and export the alarm status to an xml file. Clean with the batch script and then setup LCDHost as follows. Connector just like the others Setup the indicator Setup any text warning with conditional formulas so it doesnt appear unless the alarm is triggered. Heres the sample cleaned xml file. Quellcode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 <LogDataExport> <name> Alarm </name> <exportTime> 2013-04-07T19:57:59.5025728+10:00 ...
Are you using a background pic for the gauges or gradient fill? How did you get the tick marks to be white?
Looking good! Maybe change the scale for temperatures to read maximum at 50c
Zitat von »novax1« and to show temperatura.agua information. sampling and temperature information. external sensor but the fan out many numbers?. didnot like show flow. regards If you put this :%.2f at the end of the fanrpm data template inside the brackets it will set it to 2 decimal places. (change 2 to zero to have no decimal places) {logdata.LogDataSets.Fanrpm:%.2f} If you want to show flow as GPM instead of the default Liters per hour use this formula to convert it. {={logdata.LogDataSets....
Zitat von »novax1« este es el error que muestra cuando ejecuto XML.bat. This is the error that shows when I run XML.bat. You can try this dll dependency tool to see what dll is missing. There maybe another System DLL in the chain of dependencies that is missing. Sorry I cant help you more than that at this stage. I have windows 8 installed on my work laptop so might be able to recreate the problem later this week for you but I wouldnt count on it. http://www.dependencywalker.com/
My system runs 24/7 and experiences no crashes or memory leaks. The system stays at about 4Gb mem use most of the time and 4-7% CPU usage and I have a lot of xml log files running too for G19 monitoring. Maybe there is something else astray.
Zitat von »novax1« Saludos no se como poner el archivo creado xml.bat en el programador de tareas. El código de limpieza que le indico como tengo que usarlo y donde lo tengo que poner. [/quote]1.0 1. First run task scheduler (just type task scheduler on the windows 8 start screen and press enter and it should start) 2. Create a new task (right click "new task") 3. Change it to a system run task (click "change user or group" and type "System" under the object name and press enter) 4. Check the "...
Under full load with OCCT powersupply test. Pic of my power meters showing power drawn at wall from each PSU. Ouch!
Here's my new G19 Screens for Aquasuite 2013. I have added Aquasuite alarms to the G19 screen and critical dials & indicators on a dedicated Aquasuite screen. Main G19 Page screenshot with all ok, and screenshot with 1 pump turned off to simulate a failure. Aquasuite G19 Page screenshot with all ok, and screenshot with 1 pump turned off to simulate a failure. A Screen shot of some of the LCDHost settings for the Aquasuite page.
Zitat von »novax1« Hello and created the file and xml.bat. but not how to set it in the task scheduler. Windows 8 I can help this code as I have to put cleaning. <xsl: stylesheet xmlns: xsl = "http://www.w3.org/1999/XSL/Transform" version = "1.0"> method="xml" <xsl:output version="1.0" indent="no" omit-xml-declaration="yes"/> <xsl:template match="*"> <xsl:element name="{local-name()}"> <xsl:apply-templates select="@* | node()"/> </ xsl: element> </ xsl: template> <xsl:template match="@*"> <xsl:...
Your very close! You need to make a batch file (which I called xml.bat) and put this code in it and set it to run at startup as a system scheduled task with task scheduler. Change the timeout value to how often you want the data to update. Quellcode 1 2 3 4 5 :top C:\libxslt-1.1.26.win32\bin\xsltproc.exe -o c:\cpu-clean.xml c:\CPU.xsl c:\CPU.xml C:\libxslt-1.1.26.win32\bin\xsltproc.exe -o c:\gpu-clean.xml c:\CPU.xsl c:\GPU.xml timeout 1 goto top
Hi AC team! I have a question regarding getting the rotating fan animations to work on the overview page. I've added more fan channels and the custom control for the rotating fan animation but i dont know which data source to bind it too, to get it to work? Ive tried all the individual fan elements and values and the only one that it will accept as a data source is the 1st menu level item (fan channel) under the fans but that doesnt make it rotate?!??!
The new 2013-1 versions of Aquasuite xml export all works properly now! I managed to get the fan rpm signals displayed on the G19 too. The next big challenge is to setup a dedicated Aquasuite monitoring page for the G19.
FYI a clean win 7 64bit install with full .net 4 client and C++ updates has fixed this crash. Not sure what it was. I still however get an immediate crash when I try and add a fan sensor value to xml export.
After setting up XML data export I get the following error when I reboot and Aquasuite restarts. Currently the only way to fix this is to reinstall Aquasuite and delete existing settings when prompted. If I dont setup XML export, I can stop and restart Aquasuite fine. 1st Application Error Quellcode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 7...
Great News!!! I got it all working!!!!!!!!!!!!!! Im using 2 data connectors in LCDHost to pickup the CPU and GPU water loop temps.. I can now add anything I like from Aquasuite 2012 XML logs to the G19 screen! I had to create a seperate map file for each dataconnector and use the cleaned XML files which I cleaned with the XSL template script. (now running every 10secs as water temps dont change that quickly.) OCCT Powersupply test running in background. This shows the CPU Water Temp Data Templat...
LCDHost for G19 colour screen.. I got some scripting done to clean the xml with an "xslt" xml template to remove the xml attributes and make a clean xml file. A batch file runs every 5 secs against the aquasuite xml file to strip the stuff that LCDHost doesnt like. The problem I have now is that the Dataviewer looks like it can only handle 1 instance so I cant have seperate xml files processed by seperate dataviewers. While I can set each dataviewer to its own data source the data txt and data b...
Hi Shoggy and crew! I have a request.. Is there a way to get clean XML out of the reporting engine? The XMLNS attributes arent understood by a few programs like LCDhost that need clean XML. I can get aquasuite 2012 XML data to work fine if it is clean, but aquasuite puts the attributes in so the plugin cant parse them. example code that currently doesnt work because of the xmlns attributes. <?xml version="1.0" encoding="utf-8"?> <LogDataExport xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:x...
They are releasing another hotfix patch. The unit is supposed to reset at the 95% point and it isnt doing it. I powered off PC (normal shutdown) and unplugged from power to let A5 power down and when I restarted it has 1026 firmware loaded and all working A.OK. I waited for 3 mins while it hung at 95% before shutting down just to be sure. There is a chance you could brick your unit so if you attempt this your doing it at your own risk... Id suggest waiting for the patch. PS.. take screen shots o...
Zitat von »tpb211« I will figure out a way to split the load. Were you able to control the heat issue at 1.8amps? I would like to reduce fan speed up to 50% for majority of the time with a similiar load, really wish there was a water block for the pa2's. I may have to get creative and find a block that will work Yeah Ive been looking at blocks to use for the PA2 too. I was going to mod a spare RAMPLEX block with RAM heat plates and see if I could get it to fit across 3x PA2 transistors mounted ...