Suchergebnisse
Suchergebnisse 1-21 von insgesamt 21.
Having a new problem...can not get any device work on the aquabus anymore. Not even with the standard cables. I have 2 PowerAdjust 2 Ultra's, reset them to factory defaults, gave them a aquabus number (51 and 52). Also the Farbwerk had a reset and gave it number (21). The Aquaero had a factory reset, reconnected the devices one by one to the Aquaero, but they don't get detected. What's going on?
And it worked!! But now my Farbwerk is not connecting anymore. Not even with the original cables. ... I Updated and Rebooted through USB, restarted the pc and reconntec it, but a no go
Zitat von »GTXJackBauer« What device were you using to connect them too since some devices need a 4-pin for power. Using a PowerAdjust 2 Ultra and a Farbwerk. They work with the standard 3pin cables.... Zitat von »InfoSeeker« Did you megger the cable with an ohm meter after sleeving to confirm continuity between the two plugs? No I didn't, maybe that's what I could do..... Zitat von »sebastian« Zitat von »XenoMorpH« Then I single sleeved the cables. 20161121_163926b.jpg your cables are reversed...
This is how I created them: [attach]5924[/attach] After soldering them I used some heatshrink to protect the solder-joint [attach]5925[/attach] Then I single sleeved the cables. [attach]5926[/attach] I have no idea why it's not working..... They are not for the RPM port, fior the aquabus-port...
I created my own Aquabus / RPM signal cable. Used 2 old 3 pin female cables and soldered them togheter and sleeved them. Made 2 of them, but they don't seem to work? Does anyone has an idea why they are not working? I reconnected the standard (pretty long) cables and the devices work with my Aquaero.... But not with those 2 hand-made cables
Zitat For all existing customers with aquaero 5/6 XT or aquaduct XT (no matter how old), we grant a free license for the aquasuite 2017. The devices automatically activate the software without an additional license key. Same for all other aquaero and aquaduct customers with a total running time of less than 2160 hours (90 days continuous operation). All owners of aquastream ULTIMATE also receive a free license for the aquasuite 2017. I own a Aquaero 6 XT, bought it a while back in 2016, it has ...
Seems that NONE of the sensor software (AIDA, HWinfo, etc) shows up under System? Will do a complete Aquasuit reinstall again....mayvbe that'll help. EDIT: Nope, still not working. Even with older versions of Aquasuit
It seems that the Open Hardware Monitor sensors are no-longer availabvlein Aquasuit? I am not able to select the data source within the Overview pages, even when OHM is running in the background. Running Windows 10, AS2016-4
I managed to solve this weird problem by reinstalling aquasuit....
Aquasuit 2015-6 keeps asking to update mu Aquaero 5 LT to the latest firmware. Then I let the update run and it restarts the device....I restart Aquasuit and want to change some settings, but the it says again: Update firmware now. I have done this several times now, but I still get the same message over and over. I am using Windows 10. Edit: current firmware virsion is 2002
...I completely overlooked that optinion All fixed now, tnx!!
Is there any documentation on how to do so? I have no idea how to solve this (maybe I should make a different thread and not to hijack this 1). EDIT: Added the output and added the controller.....still not working.
I did, but it does not work. I had 2 ledstrings attached to the controller, I could only select 1; Farbwerk(1) 1-R /G/B. But I was not able to control the colors either. What am I doing wrong here
I just received my farbwerk. Connected it trough aquabus and USB. My 5LT sees the farbwerk on Bus address 20. The device also appears in the device list. I can also adjust the color settings withint the device itself using USB, but how can I control the device with the aquabus with no usb connected?
Tnx!! That did the trick !! But the tacho from 1 of my pumps is not working. So when I add it to the controller list, it shuts down even though it has 100% power. When I remove it from the list, it starts running again. With second pump/PA2 the tacho works ok and adjusting the power output works just fine.
I have the same kind of problem. I have 2 Power Adjust 2 Ultra's connected to the aquabus, On each PA I have a DDC pump running. Problem is that I can not adjust their speed. When I disconnect them from the aquabus, and connect through USB, I am able to lower the voltage and the speed goes down. What seems to be the problem then?
I have tested a bit with some different types of molex cabels I have laying around, found out that some cable have influence on the vdroop. Maybe full-copper cables have less resistance than el-cheapo copper-look-a-like cables? The fans are now running perfectly at 11.9V...weird. Tried the same on the PA2's, but the difference is minimal...0.1V at the most. Still running at 11.6-11.7V Too bad....if you say it's normal for the PA2's to have a vdroop like this, then I have to live with that. tnx !...
I'm running 3 GT's on 1 channel, 2 Corsairs FP's on a channel and 2 EK Vardar's on 1 channel. It's not that much compared to what I have seen others do...
I have 2 Poweradjust 2's (connected to my 5LT) and each of them is powering a DDC pump. When I connect the pumps the Voltage drops from 12.0V to 11.7V-11.8V. Is this normal? Same goes for my aquareo 5LT the fans are running on 11.1V