Suchergebnisse
Suchergebnisse 1-22 von insgesamt 22.
Needing some help with setting up the fill level sensor with the equalization membrane. I have it setup on the device sensor itself however the Level calibration will always show 100% even when less. Also it does not show up on the Aquaero Aquasuite settings. Any assistance would be graciously appreciated. https://imgur.com/a/jSNrujz
As for the high flow next, it will require an Aquabus cable (4 pin to mini connector). D5 next on the other hand “ Simultaneous connection of RGBpx products and aquaero 5/6 via aquabus is not possible” Might be better off connecting those two through USB via a Hubby 7 (if you need more USB connectors) Hope this helps!
Seems a bit redundant to use both. You can simply use the splitty 9 for Aquabus devices that are too far away from the Aquaero and the x4 if they’re close by.
I have an Aquaero 6 with the Aquabus High connected to a Splitty 9. What is the max number of Aquabus devices I can connect?
Good day to all, I have installed an MPS Pressure 500 to monitor the pressure across my filter, it shows the data on Aquasuite under the Pressure Sensor tab with an average pressure of 2.1 mbar. However when I go to the Aquaero tab and go to sensors, and pressure sensors, it shows 0.0 bar all the time. Is there an adjustment I need to make to show the same data? I am using an Aquaero 6 XT and have the pressure sensor connected to USB and Aquabus. Thank you for your help.
Seems strange? I just received my order and I’m from California, USA. One thing I did notice was UPS was the only option for shipment for me. Perhaps look at your postal carriers in regards to international shipments.
They may be a bit tough to find however the ol silverstone aluminum bay converter enclosures were always great. They could hold HDD,SSD, and 5.25” bay items.
Maybe a dumb question however is the X4 hub connected to Aquabus High? That would be the first thing to ensure. Is the Calitemp required to have an Aquabus high signal or could it be connected to the Low side since it’s just a temp sensor? Let me know what you find out.
How does the Vision Unit connect to the Aquaero 6 LT? Does the USB take care of that or does it need another cable to do so? Thank you
Understood however as mentioned just of interest to utilize the Aquaero to its full, and I have a small LCD in my case that has the my Aquasuite overview page.
Sad to say none of those sellers carry the equipment needed, It will have to be purchased through the Aquacomputer store. Even Aquatuning doesnt have the hardware, I'll order it from Aquacomputer and just wait for the shipping. Thanks.
I have recently purchased an Aquacomputer Pressure Sensor Delta 1000 as knowing the pressure level of my loop will be interesting. However, where can I purchase the accessories needed in the U.S. as the Aquacomputer site will have to charge me about $40 US dollars for shipping alone. Any guidance will be greatly appreciated. Thank you Update: I did see that they have a standard postage option thats only $8 but may take up to 30 days. If that is my only option then I'll have to do it.
I dont believe that it will work as the 4 pin RGB connector is not compatible with such. You might have to pick up a different RGB controller that accepts the addressable RGB or 3 pin connectors. Take a look at the new QUADRO lighting controller. Be sure to ask @Shoggy to get the final word.
Awesome work! This is pretty much a mini Aquaero in a Pump!!!! HYPE!!!!!!!!!!!
I'm making custom cables for my build and want to ditch any 4 pin molex cables period (Obviously besides my Aquaero and Farbwerk). Does anyone have a diagram to connect D5 pump directly to PSU via ATX female connector? Will it need to be through PCI connector or AUX connector? Thank you
I have a PWM D5 pump and would like to know if I can remove the molex and connect power thru the PWM header since I'll be powering it thru AQ6?
Which drive bay mounting kit are you referring to? If its the PowerAdjust one Im not too sure..... I know the farbwerk works perfect. Might want to reference @Shoggy to see if that'll work
The Quadro will be able to connect via aquabus and allow you to control your fans through Aquabus which is ideal. Although 2 would not be necessary if you connect it with its companion device the RGBpx Splitty4, so this will cover your fans. Thus a poweradjust is not necessary. And the Farbwerk will cover the LED strips however does not offer Addressable RGB lighting.
I own an Aquaero 6 XT and the screen never turns off when the computer powers down. Would someone be so kind as to direct me to the instructions to power it down. Primarily because my PC is on my desk in my room and at night its distracting while trying to sleep. Thank you.
I'm looking at the RGB Splitty 3, would this permit me to use my farbwerk and still have some addressable RGB lights? Or is that for a different purpose? Thank you Shoggy.
I got the update and everything is working great, using less CPU resources and runs smoother too. Good work AC team!
This looks amazing. Would this be worth considering if I already have a Farbwerk?