Suchergebnisse
Suchergebnisse 1-11 von insgesamt 11.
Zitat von »jdgb99« Hello, I had a problem like yours nor USB aquastream xt neither aquaero were recognised by aquasuite after windows xp start and I've found this only happens when starting aquasuite with an USB pen tablet device connected. I start windows with this device unpluged and start aquasuite, this way every thing works fine and I can plug the USB pen tablet later if I need to. I can also atart windows and unplug the tablet just before start aquasuite. Hope this will help. OMG this wor...
Zitat von »degoe« Hello, With this post I would like to ask you for your help/support. I have the Aquastream XT standard pump installed in my system running Windows XP. It is connected with USB, 12v and tachosignal cable. When I connect the pump to USB while in windows (or after reboot without the pump installed) it detects it like it should and shows up as an USB-HID controller in Device management. Aquasuite works properly then. But after a reboot windows fails to detect the pump automaticall...
Zitat von »MUFFDIVER« Darren do you have on a partition windows XP installed ? I think if you tried this to clear up any issues regarding Vista then it would make the fault finding process much faster. Just a thought is all :/ Muff Hi I have bridged the connections to my other computer that runs xp and it seemed fine, thus narrowing it down to the motherboard being faulty or vista problem... i shall have to install xp and see.... My mother board is "asus striker formula 2" ...
Zitat von »hobbes« does this: http://www.digwin.com/view/vista-bug-fix…ivers-not-found help? (it recently helped another member who uses Vista) No luck But thatnk you for the information.
Zitat von »Shoggy« Have you tried to flash it via the aquaero or with the parallel port flasher? Is the red LED on the backside flickering very fast? Ok i have finally worked out there is a setting in aquasuite that enables the led. The led is flashing red and it impulses 3 times a second... Im not sure what that means can anyone help? The model is the "aquastream xt ultra" and It currently has firmware version "1011" also have a pictue of whats happening below...
Zitat von »Shoggy« It is on the lower backside (yellow) of the pump. Nope thats not flashing at all... :O Its off
Zitat von »Shoggy« Have you tried to flash it via the aquaero or with the parallel port flasher? Is the red LED on the backside flickering very fast? I dont have the aquaero and i dont have a parallel port on my system , were is the led i should be looking at on the pump? Cheers
Zitat von »daztheraz007« Thanks for your reply and help, It currently has firmware version "1011" i shall update that and see what happens ... Ok, I used the aquastream flasher but had no joy . it seems to find it then restart the device when it does that the device cant start again, if i look in the device manager it has a triangle with a "!" sign in the middle...
Zitat von »Shoggy« A driver for the pump or our other devices does not exist. As it is programmed as a HI-Device, it does not need any drivers. Which firmware does your pump have? The latest version (1017) has a lot of improvement for the USB communication. Thanks for your reply and help, It currently has firmware version "1011" i shall update that and see what happens ...
Hi all Just wondering is theres a driver for the aquastream xt as my computer only sees it as "human interface device" The annoying thing is every time i restart my computer the device stops working and the computer is unable to "run device" I normally disable and enable the device and that fixes it, its very annoying! Any help would be great. Thank you....
Just wondering if anyone knows what graphics block i would need for my graphics card "Gainward 7800gs 512mb" If anyone could help me this would be great
27.04.2024, 06:49
Sprache ändern
Registrieren
Anmelden
