Suchergebnisse
Suchergebnisse 1-10 von insgesamt 10.
Zitat von »Shoggy« Is this with pump set to full speed? If so this can not be right and we have to assume the sensor is faulty in some way. No this is with the pump back at 3, I put it back otherwise I can get whirlpooling and bubbling in the res. I have ordered all three MPS sensors, 100,200 and 400. Once I get these I will see if my current re-calibrated sensor works when the pump is at full speed. If not then I will replace with the new MPS 400 and see if it reads at full speed and then down...
Zitat von »Shoggy« Maybe a problem with the automatic zero flow calibration. You could try to calibrate it manually. Go to the tab configuration and untick the automatic zero flow calibration. Remove power from the pump while the system is running (no problem as long as there is no load), wait a short moment to make sure that the water does not move anymore, click the button "set current flow as zero" and wait till the process is finished. Afterwards power up the pump again. Hey, thanks for the...
I will try another cable to see if on the slim chance it is that. One thing I have just seen is that on Aquasuite I am getting Raw data from the sensor regarding pressure, but this does not seem to be converting to a flow rate ?
Good news, I switched it around, rebooted and I had a flow rate of 272, but when I rebooted the software now shows nil again. So I know I now have it all the right way round which is good. However the software perhaps buggy ?
Zitat von »Shoggy« Possible that the pump will not reach the lower 80 l/h limit in this case. You could easily set the pump to full speed for a quick test. So I tried your suggestion and tried max setting on my pump and nada, so I will return the flow meter for a replacement. Now I prefer to keep my pump at level 3 as it does not push bubbles round my loop. So I am wondering, do you think I should go with the MPS 200 or 100 maybe ? Also as far as I know, the flow meter should pick up flow which...
Zitat von »Shoggy« OK, that you get a value of 0 right from the start is quite strange. You can try the following: go to the system tab and select the high flow usb sensor (53129) as device. Close the aquasuite, start it again and select the correct device type now (53132). To be on the safe side you can close the aquasuite one more time and start it again. If it still shows an unscaled value of 0 it is pretty safe to say there must be something wrong with this sensor. Unfortunately you will ha...
Zitat von »Shoggy« Was it working before? If so, what flow rate value did you get? What kind of coolant do you use? This is the first time I have ever used it, put in the loop yesterday. I am using Mayhems X1 Clear Premix (No Dyes Etc)
Zitat von »Shoggy« I meant this one: [attach]6520[/attach] Looks like my second attachment did not come through properly. However my ''Current Unscaled Value'' is 0 Thanks.
Zitat von »Shoggy« Below the diagram you have an unscaled sensor value. What does it say? Thanks for your reply. It is showing 0 for Unscaled. For clarity I have included screenshots of what I am seeing. [attach]6518[/attach] [attach]6519[/attach]
Hello All, New comer here and new to the MPS Flow 400. Long story short, I have the latest Aquasuite installed and I was prompted to update the device firmware which completed successfully. Everything seemed to be reading fine and I was getting a Temp reading, but I am not getting any information on my flow rate. I have changed my settings regarding flow rate to Litres per Min and Litres per Hour and vice versa but it did not make any difference to the flow reading as these sit firmly at 0.0. Ev...
19.04.2024, 01:09
Sprache ändern
Registrieren
Anmelden
