Ich spreche Deutsch nicht so gut. Übersetzt mit DeepL Translator (kostenlose Version) Die aktive Rückwand ist schön für die Optik, aber für die Funktion nicht erforderlich. Ich habe kein Problem mit der Entscheidung, wenn sie die Produktion nicht verzögert (>6 Monate). Der Anblick des Wassers ist reizvoll. Die Größe der Karte könnte in einem normalen/kleineren Gehäuse ein Problem darstellen. Der Block muss mit dem Cablemod-Adapter funktionieren! Eine vertikale Position ist in dieser Generation s...

4 weeks... for a reply... yikes. So it goes.

Does AC accept RMAs for "clicky" High Flow NEXTs? Mine is pretty bad to the point where I'm either going to not use it or try to get it replaced. I've had it for months but didn't want to take my whole loop apart. Now that I have... I get a lovely metronome click

Any updates on fixing time based automatic profile switching going out of sync. For me, I will set a profile 1 and a profile 2. 2 is the same as 1 except for the RGB being off. I set the profile 1 switching time at 7am and the profile 2 switch time at 10pm. So, between 10pm and 7am, profile 2 should be active. However, what ends up happening is the profiles don't switch, then out of sync, switch. Basically, it seems like the timing gets thrown off. I would assume the Aquasuite would be reading t...

Just want to double check, presently there is no way to back up fan curves/rgb settings if you have an Octo/Quadro/Farbwerk 360? Is there a file in windows (program data or some similar folder) we can back up? Seems pretty strange you can back up an overview page and nothing else.

Couple issues: 1. The time switch function for automatic profiles gets thrown off somehow. It will work for a day, but then after that, it doesn't switch profile at the specified time and then proceeds to switch profiles later. IDK if Aquasuite is using it's own internal clock or the WIndows clock... but this function is definitely not working properly. I'm not sure what is causing it. System shut down? Locking the computer? Turning off the monitor? IDK. 2. This is incredibly frustrating... unle...

Zitat von »InfoSeeker« Zitat von »paskowitz« SW:Aquasuite x.11. HWinfo v6.20-4030. HW: Octo, Farbwerk 360, 3x Splitty9s, Hubby7 (latest FW) Steps taken: Fresh install of HWinfo Bit of an odd situation. Aquasuite can detect HWinfo... but HWinfo cannot read any sensor data from Aquasuite. So, if I want to add a data source in AS, I can add from HWinfo... but if I open HWinfo, I cannot see any data from any Aquacomputer device. Sensors on the Octo can obviously be read by AS. When I had my Aquaero...

SW:Aquasuite x.11. HWinfo v6.20-4030. HW: Octo, Farbwerk 360, 3x Splitty9s, Hubby7 (latest FW) Steps taken: Fresh install of HWinfo Bit of an odd situation. Aquasuite can detect HWinfo... but HWinfo cannot read any sensor data from Aquasuite. So, if I want to add a data source in AS, I can add from HWinfo... but if I open HWinfo, I cannot see any data from any Aquacomputer device. Sensors on the Octo can obviously be read by AS. When I had my Aquaero 6XT as my controller (same version of AS and ...

Zitat "Compatible with many manufacturers Aqua Computer offers adapters such as the Splitty4 as accessories. These adapters can be used to control NZXT and Corsair products with the farbwerk 360. More adapters for other manufacturers will follow." Any plans for a 3-pin addressable RGB adapter? There are people DIY'ing it on Corsair's Commander Pro (4pin addressable), so it should be possible. ATM, 3-pin devices are relegated to mobo software hell. Also, since this is USB, I assume I could have ...