Suchergebnisse
Suchergebnisse 1-29 von insgesamt 29.
Hello Aqua Team, I have an issue with Aqua D5 pumps ... They cannot remove air and both radiators are full with air and cannot be fulled with water. Could you please advice me how to proceed ? Before that I have 2 Ultimate pumps and they has a program to remove air. Best Regards!
Thank You! My focus is on pumps - only USB cable is ok or need Bus cable ? For ATX power I think I have it. Just need to test it.
I will use that for that two pumps: https://shop.aquacomputer.de/product_inf…roducts_id=3945 ULTITOP DUAL D5 pump cover for two D5 pumps, G1/4 So I think that is not serial actually.
Sure: Temperature sensor inline G1/4 for aquaero, aquastream XT and aquaduct Temperature sensor inline G1/4 for aquaero, aquastream XT and aquaduct 8,98 EUR (incl. 19 % VAT excl. shipping costs) Shipping time: Limited stock available, delivery time to DE 1-4 business days Limited stock available, delivery time to DE 1-4 business days Product No.: 53066 Flow sensor mps flow 200, G1/4 Flow sensor mps flow 200, G1/4 49,90 EUR (incl. 19 % VAT excl. shipping costs) Shipping time: Out of stock, delive...
Hello Guys, I want to ask you how to connect all together. I have that equipment: 1. D2 Next pump - 2 pcs 2. Aquero 6 Pro - 1 pcs 3. USB Hub -1 pcs 4. RTC - 1 pcs 5. Flow sensor - 1 pcs 6. Thermal sensor - 4 pcs 7. Power switch cable for Aquero - 1pcs How to connect all them together to know that all is ok ?
Hello Guys, I have a question about aquastream ULTIMATE pump. When I use aquasuite and configure pump for curve settings pump's rpms cannot go under 3000 rpm. It is possible to put that pump on 2000 or 2400 rpm ? And how ?
Hello Guys, I am looking for most silent water pump that you have. I have two choices but you can advice me another one. My choices are : 1. D5 NEXT pump Dual 2. aquastream ULTIMATE pump Dual. What is you suggestion here ?
Zitat von »Hufeisen« See the attached Picture. [attach]7689[/attach] If you activate the Relais in the Aquasuite software, your Computer will power off. All unsaved data will be lost! If you want to power on your computer without the aquaero, you need to connect the green wires together. I have one very strange problem. So I cut the green wire and put it at 2 sides of 3-pin connector after that connect it to aquero 6. The result is when I press power button on my case power on-off for a millise...
Wow, so it was not needed probably. But it is good to have to prevent more damage.
Hello guys, I still do not have software installed. It is possible with remote control to manage pumps and fans to be most quieted and performance. How to configure profiles ?
Zitat von »EnigmaG« In my opinion, it is easier and safer to use a shutdown command via usb. A hard shutdown is only necessary if the system has hung up completely and then you have other problems. PS: Zitat Thank You! So actually it is replace power button. No, this is the power on line, as long as it is connected to ground, the Power supply is on. You connect the relay as opener in series. If you want to use the power button you have to connect the relay parallel to in as closer. I want to pu...
Zitat von »Hufeisen« See the attached Picture. [attach]7689[/attach] If you activate the Relais in the Aquasuite software, your Computer will power off. All unsaved data will be lost! If you want to power on your computer without the aquaero, you need to connect the green wires together. Thank You! So actually it is replace power button. So it will get 4 secs to cut the Power. I have all hardware and soon Software for that and just asking for tricky settings.
Hello guys, I already have power cable for power connect. I have 3-pin connector to use for Aquero 6. My question is where I can connect that 3-pin connector and how to put 3 wires on it ?
Hello guys, I have 4 Splitty 9 FAN splitters and 28 fans installed there. The configuration is like that: 1. Splitty 9 - 8 230 mm BitFenix fans 2. Splitty 9 - 8 140 mm Silent Wings 2 up to 1600 rpm -PWM 3. Splitty 9 - 8 140 mm Silent Wings 2 up to 1600 rpm -PWM 4. Splitty 9 - 4 140 mm Silent Wings 2 up to 1600 rpm -PWM How to configure Splitty's and Aquero to have all FANs between 300 and 500 rpm ?
Hello guys, I buyed one Aqua Computer pump Ultimate Version from Amazon.de it is absolutely dead. I think it is on warranty and need to do RMA I think. What is the RMA process or I need to ask Amazon for that ?
I already buy passive heat sink and wondering to get water block also to install it into heat sink. So then heat issue should be solved. I have 4 Fan ports with 4 Splitty 9 -> 8 FANs each. So my FANs issues should be solved then. how to connect 2 pumps with aquabus ? Which ports to use for communication with Aquero ? Is it USB enough or need aquabus also ?
Thank you, so my planning is perfect now.
Slitty 9 has one jumper between FAN mode 3-pin and aquabus mode 4-pin.
Thank You for your reply. So now I am sure that my planing is right. I just need to connect all together and install software to configure all.
Hello Aqua Computer experts, I need a little help with Splitty 9 and Active versions ... What are differences and how to put jumper settings for 8 - 3 pin BitFenix 230 mm FANs (I think they are not PWM) ? Did I need Quaddro here ?
Now I got your point and if it is the case then I need to think how to prepare another Power cable outside the pc case to my MO-RA 3 radiator. For another all is ok with just e Splitty 9.
That is a good plan, thank you. So just to be sure that I get clear your advice. I need quadro because I need more power for all my FANs. So then 4 port or 8 port is better for all my devices ? Actually I checked my plan again ... So I have on Aquero 4 FAN ports, I will put 4 Splitty 9 there with 8 FANs each. That is is 2.4A on each FAN port ... if Aquero is ok with that configuration all is fine by me. I will have port 1 - Splitty 9 with 8 Bitfenix 230mm FANs.- Radiator 1 Port 2 -Splitty 9 with...
I think you do not get my point... I want to put this pumps over 2 140 mm FANs with decoupling tools. And here is question ... how to fix aquastream decoupling kit with alphacool 140 mm FAN accessories bracket ? In e-shops is written that they are perfectly compatible, but in real bolt holes are not equal.
Are you sure that I need the Splitty9 Active ? In Splitty 9 have a jumper to change from 3 pin to aquabus mode, I think it should be enough.
Hello guys, I buy two Ultimate pumps (Product no.: 41108) with decoupling kit Product no.: 41129. Also have a Shagy Sandwich Product no.: 41079. I also want to use Alphacool decoupling kit Eheim/Hydor/Laing cover 4 decouplers Article no.: 52007. I have and Alphacool pump mount universal for 120-140mm fans/radiators Article no.: 52217. My question is what and how to use to mount that two pumps over the 140 mm FAN ?
Thank You for your reply. Fans are Be quiet! Pure Wings 2 - 140 - 1600rpm (140x140x25mm): General Specifications Model: Pure Wings 2 140mm Revolutions at 12V (RPM): 1,600 Displacement volume at 100% (cfm, m3/h): 94.2 / 160 Air pressure at 12V (mm H2O): 1.82 Volume @ 25% / 50% / 100% (dB(A)): 16.1 / 24.1 / 37.3 Mechanical Specifications Dimensions (LxWxH): 140 x 140 x 25mm Bearing technology: rifle Motor technology: 4-pole fan motor Cables and Connectors Connector plug: 4-pin Cable length: 450mm ...
Hello guys, I buyed aquero 6 PRO controller and need a little help with cabling... I have 1. 28 pcs - 140mm PWM fans that wan to connect there. I think to use 4 Splitty with 9 ports each. 2. 2 pumps, 3. Flow sensor, 4. 4 temperature sensors - water 5. 4 temperature sensors Air. 6. Real-time clock. Also do you have special cabling connection for PSU and how to connect PSU cable for emergency ?
To be more clear I will say it like that ... Did I need to have any device to be connected by aquabus ? Did I need all devices to be connected by USB ? Did I need USB hub for that ? If I use Splitty for 8 Fans what cable need to use to controller ? 4-pin PWM or 3-pin is ok ?
Hello Guys, I buy a lot of Aqua Computer equipment and want to know ... more about cabling. I have: 1. 2 Pumps - Ultimate 2. Controller 6 PRO 3. Flow Sensor 4. 4 Thermal sensors 5. 9 ports PWM splitter 6. Filter 7. Remote Control IR 8. Real Time Clock What kind of cables and connectors I need to buy to have a complete solution ?
16.04.2024, 21:58
Sprache ändern
Registrieren
Anmelden
