Suchergebnisse
Suchergebnisse 1-22 von insgesamt 22.
Zitat von »InfoSeeker« Zitat von »D11125225« I’ve got dual loop system but both loops have similar layouts, I have got M5 connectors running out of my dual Mps delta 40 sensors into G1/4 connectors using relevant tubing, both high and low sides are connected in the loop lines where flow is running out of other components to the radiators, I am trying to measure any differentials in the pressure in case of situations like pump failure or cloggings.. etc, I have attached couple of photos for illu...
Zitat von »InfoSeeker« Zitat von »D11125225« I’ve got dual loop system but both loops have similar layouts, I have got M5 connectors running out of my dual Mps delta 40 sensors into G1/4 connectors using relevant tubing, both high and low sides are connected in the loop lines where flow is running out of other components to the radiators, I am trying to measure any differentials in the pressure in case of situations like pump failure or cloggings.. etc, I have attached couple of photos for illu...
Zitat von »Dops« what do you want to use the sensor for? on page 27 says the sensor only has M5 connectors. Have you installed it yet? What do you want to monitor with it? Zitat von »InfoSeeker« Zitat von »D11125225« Hi Not sure if I reed this the right way but does section 6.4 in the manual says I could place the sensor basically anywhere in the loop using M5 and G1/4 push-in threads because thats what my current layout looks like, I haven’t filled the loop yet but I leak tested with air pump ...
Any ideas if this layout is correct? I can provide more details if necessary.
Hi Not sure if I reed this the right way but does section 6.4 in the manual says I could place the sensor basically anywhere in the loop using M5 and G1/4 push-in threads because thats what my current layout looks like, I haven’t filled the loop yet but I leak tested with air pump and everything seems fine and ready to go, I don’t want to use the sensor as a fill level sensor but I’ve got the membrane sitting on top of my reservoir at the moment.
Hi all, I'm planning to fully occupy hubby7 as previously suggested to me when inquiring about suitable build for my dual loop based system, but I noticed ports 3,5,7 only 4-pins, is it ok to connect 5-pin usb devices/sensors to hubby7 using only 4-pins?
Zitat von »InfoSeeker« Zitat von »D11125225« I have bought the alternative ones, single one fits the sensor’s m5 and screws in perfectly but issue is you can’t but second one next to the other, there has to be another solution !? I am not following you, can you provide links to what you have? Zitat the one I bought did not come with an o-ring, is there a link to the o-ring that I should be using ? I suspect most any 5mm ID O-ring would do... HERE are 4 posibilities from your vendor, 2 materials...
Zitat von »InfoSeeker« The specs look right. EDIT: make sure you get an O-ring for the male M5 end. I have bought the alternative ones, single one fits the sensor’s m5 and screws in perfectly but issue is you can’t but second one next to the other, there has to be another solution !? the one I bought did not come with an o-ring, is there a link to the o-ring that I should be using ?
Zitat von »InfoSeeker« It may take two steps: M5 to G1/8G1/8 to G1/4 Is the adapter in the link below good substitute for the first one ? https://uk.rs-online.com/web/p/pneumatic…aptors/8656027/
Hi all, recently bought delta 40 pressure sensor and noticed small inlets and outlets, after a quick search I came across this connector but this is for soft tubing, any Hardline substitute for it ?
Questions left to be answered Is there any other ambient temperature sensor other than AQ that is compatible with one of these products (OCTO/Farbwerk/Flow Mps/Pressure Mps)? In terms of EK Cpu and Gpu blocks, will they work if I hooked them up straight away with farbwerk without any adapters using drgb headers on farbwerk?
Zitat von »Taubenhaucher« The D5NEXT can control 90 LEDs, unfortunately I have no answer for the other questions. I guess this will definitely be plenty for 4-6 rgbpx strips.
Zitat von »Bartdude« The MPS-400 will be fine if your running 2x D5 in series, I have this with my 2x EK D5 Duel Revo. At 100% pump speed I can achieve 365lh. The only thing I recommend you add would be this. I had difficulty with my MPS not working until 1 day whilst topping up my res I noticed without the lid on my MPS was working fine, added the pressure relief and its worked fine ever since, 3 years so far much appreciated, added the membrane to my list !
Apologies for stretching out this post but I have been doing final reviews and I came through these questions: Is there any limit to how many RGBpx strip i can daisy chain to connect to D5 next pump? I know there is a max of 65W for the pump but not sure how much each strip consume. Is there any other ambient temperature sensor other than AQ that is compatible with one of these products (OCTO/Farbwerk/Flow Mps/Pressure Mps)? In terms of EK Cpu and Gpu blocks, will they work if I hooked them up s...
Zitat von »InfoSeeker« For the 2-pin temp extensions you can use 82052 or 82053, or build your own. I believe the adapter for RGBpx to GPU/CPU connectors will be THIS. And the RGBpx cables can be from this LIST, depending on length needed. top man! great this should be a complete list now, thank you everyone for the advices.
Zitat von »Taubenhaucher« Do I understand your list correctly and you want to buy an additional USB cable for each device? All devices that connect via USB come with the appropriate cable. With the MPS 400 the question arises whether 80 l/h as a lower measuring limit for a PC water cooling might not be too high, depending on the installed radiators, cooling blocks and fittings I would rather tend to the MPS 200, because a flow of more than 200 l/h is ilusory in most computers, but a flow of 40 ...
Many thanks for all suggestions mates I have made up my mind finally to go non-aquaero route finally, so just as a final stage I would like to check the final list including necessary cable connections: Qty 2 - D5 Next RGB ( Item No.41118 ) Qty 2 - Mps Pressure sensor delta 40 ( Item No.53133 ) Qty 2 - Mps Flow rate sensor 400 ( Item No.53132 ) Qty 2 - Inline Temp sensor ( Item No.53066 ) Qty 1 - Ambient Temp sensor ( Item No.53026 ) Qty 1 - OCTO Fan controller ( Item No.53286 ) Qty 1 - Farbwerk...
Zitat von »xdecock« You can definitively control multiple fan With a splitter from a single control port. So the quadro won't be useful. Ek rgb need an rgbpx to asus header adapter and are "in only" from what i know. Basically here, you'll have 2 rgbpx port So adding a farbwerk is probably a good idea. In your case, i'll limit the aquabus to the pressure / flow sensors. The goal of aquabus is to allow your aquaero to centralize sensor data and act on the signals to trigger alarm, shutdown your ...
Zitat von »xdecock« From what i read you'll want an aquaero. This will gives you 4 fan control. 2 flow control. 1 aquabus. Your 2 pump provide 2 additional fan port You'll need in your projected setup 7 usb port. Aquaero + 2 pump, 2 flow, 2 pressure. From there, do you need 8 fan controller channel, if so i'll add a quadro this will require an additional usb port ( the hubby takes only 1/2 usb header so that should be all right) This will provides for each device a tab in aquasuite. If you want...
I'm looking for a way to run the following on Aquaero 6 XT and to be able to control them all independently: 2 D5 Next pumps 2 AQ Mps pressure sensors delta 1000 2 AQ Mps 400 flow rate sensors 2 AQ inline temperature sensors 1 AQ ambient temperature sensor 8 Noctua NF-A14 pwm chromax fans Also if possible rgb wise I'm looking to hook up double AQ led strips along with cpu block and 3 gpu blocks to be controlled via aquaero. what hubs do I need? when should I daisy chain via splitters? will there...
16.04.2024, 07:02
Sprache ändern
Registrieren
Anmelden
