Suchergebnisse
Suchergebnisse 1-13 von insgesamt 13.
Zitat von »Hufeisen« There is only one way to make the Leakshield work with two reservoirs. You must connect both reservoirs to the Leakshield at the same time. Run a Hose from both reservoir tops, and use a T-Connector to connect both Hoses to the Leakshield. All other solutions have their problems, and may not work reliable during an emergency. Ok so maybe I don’t understand what you mean. This is an ultitube d5 with leakshield on top. How do you connect reservoir tops? It’s not possible to c...
Zitat von »Remayz« no offense taken My idea was that, if the FLT is the highest reservoir, i would connect the standalone leak shield on its fill port. It would work the same as on top of an ultitube as long as the inlet has access to air in the reservoir (not overfilled). Guess I just need to make sure that the top of the tube is well above the other FLT120 on the rear mount.
Zitat von »Remayz« get a standalone leakshield and put it on top of the loop? No offense meant but Leakshield is awesome... when used with the ultitube. The standalone leaves a lot to be desired from what I understand. Basic outlook is that Leakshield needs to be higher than the other reservoir then?
Zitat von »Hufeisen« Zitat von »InfoSeeker« If you have a leak, the leakshield actually causes air to be introduced into the loop. This can be a major problem when you have two reservoirs. Depending on the location of the leak, the introduced air can empty the reservoir without the Leakshield, and pulling all water into the reservoir with the Leakshield attached. If the Reservoir with the Leakshield cannot take in all the water from the other reservoir and overflows, the Leakshield cannot preve...
I figured but just making sure because of placement. The leakshield will be top of the ultitube and basically level with the flt120 on the other side. I’m hoping it removes all the air from the other res but does the ultitube need to be higher up?
I have an O11xl and a standard flt120 from Ek I was planning to use on the rear fan mount, but is this compatible in the system with leakshield ultitube d5? I want more water capacity but not sure if using that config will be ok with leakshield.
Zitat von »Stephan« Maybe you have damaged the probe during the hard tube install. Try to change the probes at the OCTO headers and check if the problem will switch to another sensor input. I doubt it, but will try. I also have brand new ambient probes that aren't reading at all when I use them in Octo.
I just got a new Leakshield device but I wanted to power it briefly from another PC while I did fill and test. If I install AS to a laptop and use the usb connector that is for external USB-A will it register again on my main PC or not? I know it registers when you start, but how does it work if you transfer a device to a different PC?
Yes. Restarted and now reset Octo... still nothing.
One sensor is actually a new one but the other is the same. If I reset can I reload the same profiles?
Hello, I've been running temp probes for in-line water and also ambient through my Octo for months now, but when I installed hard tubing this weekend I booted and it updated to x.47. Now I noticed that none of my thermal probes are showing up in the Octo menu in fact it is "--" reading while still have the same naming on the sensors so I know it wasn't reset. Anyone else lose probe use with this version? Is there a workaround?
This happened to me endlessly to the point where I just closed AS while I played Warzone. I am on x47 now and so far it hasn't happened yet so fingers crossed it was accidentally fixed.
Hello, I've been running x.47 and I recently tore down my build and put new tubing in and so forth while adding a new Farbwerk. However, when I loaded into Aquasuite none of my thermal sensors attached to Octo show up anymore. Is there a way to upload a support dump?
18.04.2024, 08:22
Sprache ändern
Registrieren
Anmelden
