Suchergebnisse
Suchergebnisse 1-19 von insgesamt 19.
I made some changes, I build a 5 cm long fanduct, wich is much more quiet. . I put my v-core @ 1.65 again, And mu idle temp now is 43C witch papst @ 12v and 2 outake fans @ 12v. I will upload my water temp in a minit..
Hmm, my water seems to warm up quickly, my temps started at 35 degrees, and then slowly it rises to 52 ( At the moment ) My v-core is 1.95v and I'm running 2500 MHZ With my XP 2400+. How can I get my water temp down?
I expected low 40, but when I start thinking about it. I realised my temp was 60 degrees before. at same noice level. now it is 49. I turned mij papst so now its blowing @ 7 volt and 2 outtakes behind. My temp is instead of 56!! ( with case closed and papst sucking) 49 so I won 7 degrees ( case closed and papst blwoing). And yes I'm below the roof
Thermometer slaat over de 42 graden heen bij meten van water temp The water temp is over 42 degrees!!!! in 1 sconde it goves 41.7 and the it crashes
I can set a picture online, of someone can tell me how, and has some space on the net
I the front of the case... on the floor,with 1 outtake fan sucking Damn, case temp rises to 40 Degrees
Oh and everything is with case open, so.....
temp is 47 again, water seems to warm up fast ( till 48 C ) I have an Albatron Kt400 ( Maby a lousy temp sensor?)
Hmm. ok I removed a bit of AS 3 , wasn;t much on it biut just to try, At the momentn mijn temp is 45 C Stabel, I will check again after a few mins
A Papst ( low noice ) at 12 V It doesn't blow but it sucks as you know what I mean See you in a minit, gonna check AS 3
I used AS 3 I will check now how much there is on it Can I lay down my case with everything in it? I have the 3 nase halterung ( oder so ) oh and ehm I have a little over clock: 14x150 to small to increase temp 2000@2100 Vcore is still the same
I have an T-bred 2400+ Room temp I dont know but my case tem is ( wich is open ) : 35 C
Today I installed my Aqua computer kit, I have an Evo 120, A normal Cuplex cpu cooler and The hydor L20. The water flows on this way: Hydor - Cuplex - evo 120 - Aquatube- hyfor. Now my CPU temp is 48 C idle en 53 full load. That's kinda high isn't it? If you need more info to answer my question, feel free to ask And when writing an english answer is to hard for you, try German ;D GuPPie ( Niederländer )
Yeah I think I will do that, The master slave thing is 70 euro, and I still think there should be a cheaper way. But I will go for the swich thing. Anybody some other ideas? maby a relais?
I didn't found that powerpoint where shall i look and and whats a normal name for it, I dont think the will call it a master slave powerpoint
hmm, I think I will buy this thing and I will put 12 HP delta 120mm on it they are 36 watt each what kind of powersuply you guys think I should use p.s. I can't write German but I can read it, so please reply in German I'm Dutch
Ok thats where I was looking for, but do they sell that at AQUA Computers or do I have to look somewhere else? And where is somewhere else? Maby in holland aswell?
Hello I'm from holland so I will write english to make my self clear. I wanna know if I can buy something wich will turn my pomp on when my pc goes on. and if I can't buy it, how can i make it?
23.04.2024, 11:21
Sprache ändern
Registrieren
Anmelden
