12.11.2025, 03:35
Sprache ändern
Registrieren
Anmelden
Du bist nicht angemeldet.
moe
Senior Member
Re: Fill/bleed and flush a system
Montag, 3. März 2003, 23:27
hi and welcome...
i think, it would be not bad, if you install a T-part (in german t-stück) to plug a piece of tube with an cork to flush out.
for refilling the tip ahead would be the only possibility and is really easy to realize
greetz
i think, it would be not bad, if you install a T-part (in german t-stück) to plug a piece of tube with an cork to flush out.
for refilling the tip ahead would be the only possibility and is really easy to realize
greetz
EpS
Senior Member
Re: Fill/bleed and flush a system
Montag, 3. März 2003, 23:33
Zitat von »Flying_Dutchman«
[klugscheiß]The right grammer would look like this: "Unplug all cables and lay your case on its back..."[/klugscheiß]
Sorry, ich weiß nich, was Klugscheiß auf Englisch heißt...
;D
Der war gut...
Aber Recht hast du. Hab auch kurz überlegt und mich dann fürs falsche entschieden...
454-bigblock
Senior Member
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 00:05
Thanks!
Figured the filling tip out within seconds after posting ;D
Another question:
Will the P&Q plugs work with silicone tubing with the same messurements?
-Hugo
No, you should´t do that. AC advises trongly to use PUR-tubings, because Silicon is too soft to fit corrrect.
Where are you from?
Aktuelle Statistiken von aquacomputer bei seti@home gibt´s hierWARNING: The modding-stunts in this forum were made by unprofessional lazy fools an therefore should not be performed by anyone, anywhere for any reason!
454-bigblock
Senior Member
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 00:08
no way, jose!
only PUR-tubes... silicone is way to soft! your system would leak like a women during her period! ;D
Ui! Du bist ja krass :-)
Aktuelle Statistiken von aquacomputer bei seti@home gibt´s hierWARNING: The modding-stunts in this forum were made by unprofessional lazy fools an therefore should not be performed by anyone, anywhere for any reason!
kampfsau
God
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 00:31
OK, I´ll probably order the stuff with 10mm hose plugs instead then. Not a big fan of L-plugs..
L-Plugs?
i think you´re mistaken... the PnC-plugs come in 2 versions: straight and L-type... it depends which suits you better
but trust me: the PnC-system is WAY more efficient... it´s a well tested model taken from air-pressure equipment and works absolutely leak-free! (of course if you connect it right ;D )
my first watercooling system had a mix of hose-plugs and PnC-connectors... after the first installation i had already ordered PnC-stuff for the rest of my system, i was astonished of the effectiveness and yet the simplicity of the PnC-system!
trust us users on this one...
there is no gravity - the world sucks
woodstock
God
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 11:55
HeyHey!
Look at this! Most of the People have used the P&C System and as you can see, the PUR hose can be bend in a relatively small radius. As far as I know it can be bend a lot better than silicon tubing because it will not fold as easy as silicon!
Woodstock
edit:
ojo's Case
Akula's case
frolicfresser´s case
Look at this! Most of the People have used the P&C System and as you can see, the PUR hose can be bend in a relatively small radius. As far as I know it can be bend a lot better than silicon tubing because it will not fold as easy as silicon!
Woodstock
edit:
ojo's Case
Akula's case
frolicfresser´s case