28.07.2025, 14:12
Sprache ändern
Registrieren
Anmelden
Du bist nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies dein erster Besuch auf dieser Seite ist, lese dir bitte die Hilfe durch. Dort wird dir die Bedienung dieser Seite näher erläutert. Darüber hinaus solltest du dich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutze das Registrierungsformular, um dich zu registrieren oder informiere dich ausführlich über den Registrierungsvorgang. Falls du dich bereits zu einem früheren Zeitpunkt registriert hast, kannst du dich hier anmelden.
moe
Senior Member
Re: Fill/bleed and flush a system
Montag, 3. März 2003, 23:27
hi and welcome...
i think, it would be not bad, if you install a T-part (in german t-stück) to plug a piece of tube with an cork to flush out.
for refilling the tip ahead would be the only possibility and is really easy to realize
greetz
i think, it would be not bad, if you install a T-part (in german t-stück) to plug a piece of tube with an cork to flush out.
for refilling the tip ahead would be the only possibility and is really easy to realize
greetz
EpS
Senior Member
Re: Fill/bleed and flush a system
Montag, 3. März 2003, 23:33
Zitat von »Flying_Dutchman«
[klugscheiß]The right grammer would look like this: "Unplug all cables and lay your case on its back..."[/klugscheiß]
Sorry, ich weiß nich, was Klugscheiß auf Englisch heißt...
;D
Der war gut...
Aber Recht hast du. Hab auch kurz überlegt und mich dann fürs falsche entschieden...
454-bigblock
Senior Member
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 00:05
Thanks!
Figured the filling tip out within seconds after posting ;D
Another question:
Will the P&Q plugs work with silicone tubing with the same messurements?
-Hugo
No, you should´t do that. AC advises trongly to use PUR-tubings, because Silicon is too soft to fit corrrect.
Where are you from?
Aktuelle Statistiken von aquacomputer bei seti@home gibt´s hierWARNING: The modding-stunts in this forum were made by unprofessional lazy fools an therefore should not be performed by anyone, anywhere for any reason!
454-bigblock
Senior Member
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 00:08
no way, jose!
only PUR-tubes... silicone is way to soft! your system would leak like a women during her period! ;D
Ui! Du bist ja krass :-)
Aktuelle Statistiken von aquacomputer bei seti@home gibt´s hierWARNING: The modding-stunts in this forum were made by unprofessional lazy fools an therefore should not be performed by anyone, anywhere for any reason!
kampfsau
God
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 00:31
OK, I´ll probably order the stuff with 10mm hose plugs instead then. Not a big fan of L-plugs..
L-Plugs?
i think you´re mistaken... the PnC-plugs come in 2 versions: straight and L-type... it depends which suits you better
but trust me: the PnC-system is WAY more efficient... it´s a well tested model taken from air-pressure equipment and works absolutely leak-free! (of course if you connect it right ;D )
my first watercooling system had a mix of hose-plugs and PnC-connectors... after the first installation i had already ordered PnC-stuff for the rest of my system, i was astonished of the effectiveness and yet the simplicity of the PnC-system!
trust us users on this one...
there is no gravity - the world sucks
woodstock
God
Re: Fill/bleed and flush a system
Dienstag, 4. März 2003, 11:55
HeyHey!
Look at this! Most of the People have used the P&C System and as you can see, the PUR hose can be bend in a relatively small radius. As far as I know it can be bend a lot better than silicon tubing because it will not fold as easy as silicon!
Woodstock
edit:
ojo's Case
Akula's case
frolicfresser´s case
Look at this! Most of the People have used the P&C System and as you can see, the PUR hose can be bend in a relatively small radius. As far as I know it can be bend a lot better than silicon tubing because it will not fold as easy as silicon!
Woodstock
edit:
ojo's Case
Akula's case
frolicfresser´s case