• 05.04.2026, 19:29
  • Registrieren
  • Anmelden

  • Du bist nicht angemeldet.

 

Proper connection Aquaero 6 PRO + D5

Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies dein erster Besuch auf dieser Seite ist, lese dir bitte die Hilfe durch. Dort wird dir die Bedienung dieser Seite näher erläutert. Darüber hinaus solltest du dich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutze das Registrierungsformular, um dich zu registrieren oder informiere dich ausführlich über den Registrierungsvorgang. Falls du dich bereits zu einem früheren Zeitpunkt registriert hast, kannst du dich hier anmelden.

Marucins

Junior Member

Proper connection Aquaero 6 PRO + D5

Donnerstag, 7. Mai 2015, 19:08

I bought Aquaero 6 Pro and D5 pump.
I Includes USB cable and 3 pin.

1. How do I connect the pump to the aquaero to fully control it?
2. Do I need to buy a 4 pin cable Aquabus?

InfoSeeker

Senior Member

Donnerstag, 7. Mai 2015, 20:31

From your post I will assume you have the Aqua Computer D5 pump motor with USB and aquabus interface

If so, you can use the 3 pin aquabus cablle included with the pump. The aquabus connectors on the D5 & aquaero are 4 pin, but only 3 pins are used.
use the aquabus plug on the D5 and the aquabus high on the aquaero



EDIT: did you get a satisfactory resolution to your reservoir top and clamp needs?

Dieser Beitrag wurde bereits 3 mal editiert, zuletzt von »InfoSeeker« (7. Mai 2015, 20:35)

Marucins

Junior Member

Donnerstag, 7. Mai 2015, 21:21

Zitat von »InfoSeeker«

From your post I will assume you have the Aqua Computer D5 pump motor with USB and aquabus interface

If so, you can use the 3 pin aquabus cablle included with the pump. The aquabus connectors on the D5 & aquaero are 4 pin, but only 3 pins are used.
use the aquabus plug on the D5 and the aquabus high on the aquaero
[attach]5250[/attach]
[attach]5251[/attach]

EDIT: did you get a satisfactory resolution to your reservoir top and clamp needs?


You're right I have exactly this the D5 pump.
I was afraid that I bought the wrong cable. In addition, I bought a 90 cm 3 pin.

Confusing is the 4 pin plug and 3 pin cable added.
This manual should be about the information that they act only 3 wires in the Aquabus :)

Thanks!

InfoSeeker

Senior Member

Donnerstag, 7. Mai 2015, 21:32

Actually, to confuse things a bit, the aquabus is a 4 pin bus, but the 4th pin is +5v (I think) and is used by other MPS devices using the aquabus ( i.e. flow sensor & pressure sensor).
You can use a 4 pin aquabus cable on the D5 pump, but it simply ignores the 4th pin.

Marucins

Junior Member

Donnerstag, 7. Mai 2015, 22:39

I have a sensor http://shop.aquacomputer.de/product_info…roducts_id=2294 connect it under the aquaero - FLOW socket?

Shoggy

Sven - Admin

Donnerstag, 7. Mai 2015, 23:35

Yes, with that cable.

Marucins

Junior Member

Freitag, 8. Mai 2015, 06:17

OK
I have this cable.

I wanted to make sure that connected to the FLOW or Aquabus

Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Marucins« (8. Mai 2015, 06:23)

Ähnliche Themen