• 22.08.2025, 14:27
  • Registrieren
  • Anmelden

  • Du bist nicht angemeldet.

 

Aquabus / RPM signal cable 3 pins problems

XenoMorpH

Junior Member

Aquabus / RPM signal cable 3 pins problems

Dienstag, 27. Dezember 2016, 23:22

I created my own Aquabus / RPM signal cable. Used 2 old 3 pin female cables and soldered them togheter and sleeved them. Made 2 of them, but they don't seem to work?
Does anyone has an idea why they are not working? I reconnected the standard (pretty long) cables and the devices work with my Aquaero.... But not with those 2 hand-made cables :(

InfoSeeker

Senior Member

RE: Aquabus / RPM signal cable 3 pins problems

Mittwoch, 28. Dezember 2016, 13:51

Zitat von »XenoMorpH«

I created my own Aquabus / RPM signal cable. Used 2 old 3 pin female cables and soldered them togheter and sleeved them. Made 2 of them, but they don't seem to work?
Does anyone has an idea why they are not working? I reconnected the standard (pretty long) cables and the devices work with my Aquaero.... But not with those 2 hand-made cables :(

My initial thought is an open, or you crossed the wires... can't be much else.

Curious, what are you connecting to the RPM signal port?

XenoMorpH

Junior Member

Mittwoch, 28. Dezember 2016, 16:11

This is how I created them:

20161121_152316b.jpg


After soldering them I used some heatshrink to protect the solder-joint

20161121_154410b.jpg


Then I single sleeved the cables.

20161121_163926b.jpg


I have no idea why it's not working.....

They are not for the RPM port, fior the aquabus-port...

Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »XenoMorpH« (28. Dezember 2016, 16:13)

GTXJackBauer

Full Member

Mittwoch, 28. Dezember 2016, 22:36

What device were you using to connect them too since some devices need a 4-pin for power.

InfoSeeker

Senior Member

Mittwoch, 28. Dezember 2016, 23:11

Did you megger the cable with an ohm meter after sleeving to confirm continuity between the two plugs?

sebastian

Administrator

Donnerstag, 29. Dezember 2016, 07:12

Zitat von »XenoMorpH«

Then I single sleeved the cables.

20161121_163926b.jpg
your cables are reversed! Compare the pin numbers on each side of the cable.

XenoMorpH

Junior Member

Donnerstag, 29. Dezember 2016, 11:42

Zitat von »GTXJackBauer«

What device were you using to connect them too since some devices need a 4-pin for power.
Using a PowerAdjust 2 Ultra and a Farbwerk. They work with the standard 3pin cables....

Zitat von »InfoSeeker«

Did you megger the cable with an ohm meter after sleeving to confirm continuity between the two plugs?
No I didn't, maybe that's what I could do.....

Zitat von »sebastian«

Zitat von »XenoMorpH«

Then I single sleeved the cables.

20161121_163926b.jpg
your cables are reversed! Compare the pin numbers on each side of the cable.

:S I think you are right :pinch:
Looking at this:

I now see that black and yellow are reversed. :whistling: Stupid me!
I'll try it out this evening Tnx!! :D

XenoMorpH

Junior Member

Donnerstag, 29. Dezember 2016, 22:24

And it worked!! But now my Farbwerk is not connecting anymore. Not even with the original cables. :thumbdown: ... I Updated and Rebooted through USB, restarted the pc and reconntec it, but a no go ;(

XenoMorpH

Junior Member

Sonntag, 8. Januar 2017, 14:17

Having a new problem...can not get any device work on the aquabus anymore. Not even with the standard cables.

I have 2 PowerAdjust 2 Ultra's, reset them to factory defaults, gave them a aquabus number (51 and 52).
Also the Farbwerk had a reset and gave it number (21).

The Aquaero had a factory reset, reconnected the devices one by one to the Aquaero, but they don't get detected. What's going on? :wacko:

XenoMorpH

Junior Member

Dienstag, 10. Januar 2017, 22:42

No one? ;(

InfoSeeker

Senior Member

Dienstag, 10. Januar 2017, 23:33

Your best bet may be to shoot tech support a message at support@aqua-computer.de

Ähnliche Themen