Koolance 1/4"(6mm) Tubing

Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.

larsiano

Newbie

Koolance 1/4"(6mm) Tubing

Freitag, 25. März 2005, 19:57

Hi,
My question:
Is it posible to fit a Koolance 1/4"(6mm) tube on an Aqua Computer Cuplex Pro P4-478
& The aquagraFX Komplettkühler 6800 Revision 2 ;D
Any advice would help :o :

cheers,

back_orifice

God

Re: Koolance 1/4"(6mm) Tubing

Freitag, 25. März 2005, 19:58

What is this "Koolance"? ???

Timstone

Full Member

Re: Koolance 1/4"(6mm) Tubing

Freitag, 25. März 2005, 20:18

No links to other manufacturers please

Men may control the free world, but women control the boobs. Brent in Player vs. Player

larsiano

Newbie

Re: Koolance 1/4"(6mm) Tubing

Freitag, 25. März 2005, 23:03

Zitat von »back_orifice«

What is this "Koolance"? ???

It's the case as shown above with build in radiator +dual pump (1000L/h) & reservoir.
All the tubes have the 1/4" size :-/

back_orifice

God

Re: Koolance 1/4"(6mm) Tubing

Freitag, 25. März 2005, 23:22

It is possible to use the Plu'n'Cool Adapters for Radiators und connect the cooler with the radiator by 8/6mm tubes...

Top_Nurse

Senior Member

Re: Koolance 1/4"(6mm) Tubing

Samstag, 26. März 2005, 00:33

Zitat von »larsiano«

It's the case as shown above with build in radiator +dual pump (1000L/h) & reservoir.
All the tubes have the 1/4" size :-/

Well...not really. The problem is that the pneumatic fittings used by A-C are designed for a specific outside diameter (OD) hose. Their hose is 6mm ID and 8mm OD. The Koolance hose is 6mm ID and 9mm OD. But there is a solution! I believe you can use A-C hose on your Koolance coolers and radiator parts as the Koolance devices use ferrel-less compression fittings that need 6mm ID hose and I don't think the extra 1mm on the OD will affect the nut from going over the tubing.

You can find some similar issues at http://www.hardforum.com/showthread.php?…3&page=29&pp=40 and also at my homepage: http://home.earthlink.net/~topnurse/

Another possible solution is to change over the G 1/8 fittings on your A-C cooler to the one you need. You can see this discussion also at the [H]ardForum link listed above. ;D

Top_Nurse

Senior Member

Re: Koolance 1/4"(6mm) Tubing

Samstag, 26. März 2005, 18:18

Zitat von »back_orifice«

What is this "Koolance"? ???

I think you guys need to get out and about more

SNTmods

Junior Member

Re: Koolance 1/4"(6mm) Tubing

Dienstag, 29. März 2005, 18:46

Without messing with the Koolance setup you can just switch out the AC water block supplied fittings for some Koolance compatible barb fittings. I have a bunch of them.

-Dan

Was an early adopter of Aqua-Computer watercooling in the U.S.