You are not logged in.
Dear visitor, welcome to Aqua Computer Forum. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.
Hi zusammen,
seit dem Update auf X.67 habe ich vom Leakshield zu den Nachpumpzeiten bereits mehrere Druckverlust-Warnungen bekommen. Vorher hatte ich keine einzige und das System ist soweit in Ordnung (praktisch kein Leak im Normalbetrieb erkennbar, abgesehen von Schwankungen durch Temperaturänderungen).
Ich vermute, dass die Schwankungen, welche durch die Unterdruck-Anpassung ausgelöst werden, selbst den Alarm auslösen.
Die manuellen Einstellungen für den Unterdruck scheinen irgendwie auch immer wieder verloren zu gehen, auch die Alarm-Settings wurden bereits einmal wieder zurückgesetzt. Ich habe hier jedoch noch kein Muster erkennen können, wann das passiert (evtl. Standby/Reboot...?)
Ist hier bereits was bekannt? Kann ich weitere Daten zur Analyse bereitstellen?
Same problem here after the update to X.67, never had this problem before.Hi everyone,
since the update to X.67 I have already received several pressure loss warnings from the Leakshield during the post-pumping times. I didn't have one before and the system is fine so far (virtually no detectable leak in normal use, apart from fluctuations due to temperature changes).
I suspect that the fluctuations caused by the negative pressure adjustment themselves set off the alarm.
The manual settings for the vacuum somehow always seem to get lost, and the alarm settings have already been reset once again. However, I have not yet been able to identify a pattern as to when this happens (possibly standby/reboot...?)
Is anything already known here? Can I provide more data for analysis?
Das Problem habe ich jetzt auch. Seit dem Update auf X.67 bekomme ich die Warnung das ich einen Leak hätte. Vorher hat das System ohne Probleme bzw. Warnungen funktioniert.Same problem here after the update to X.67, never had this problem before.Hi everyone,
since the update to X.67 I have already received several pressure loss warnings from the Leakshield during the post-pumping times. I didn't have one before and the system is fine so far (virtually no detectable leak in normal use, apart from fluctuations due to temperature changes).
I suspect that the fluctuations caused by the negative pressure adjustment themselves set off the alarm.
The manual settings for the vacuum somehow always seem to get lost, and the alarm settings have already been reset once again. However, I have not yet been able to identify a pattern as to when this happens (possibly standby/reboot...?)
Is anything already known here? Can I provide more data for analysis?
This post has been edited 1 times, last edit by "ICop" (Mar 17th 2023, 5:46pm)
This post has been edited 3 times, last edit by "TestXpress" (Mar 21st 2023, 9:15pm)
Moin, im Anhang die Selbstdiagnose im eingebauten Zustand. Diese zeigt keine Probleme an. Laut Aquasuite ist der Zustand bei 99%Als erstes bitte einmal die Membrane mit den Diagnose-Funktionen unter System testen. Wenn die Membrane verstopft, so pumpt das LEAKSHIELD den Unterdruck nach und erreicht diesen. Durch die verstopfte Membrane ist der gemessene Unterdruck aber zu hoch. Diese gleicht sich anschließend wieder aus und LEAKSHIELD muss erneut pumpen. Dieser Effekt kann sehr schnell hintereinander zu einer Auslösung des Alarms führen.
This post has been edited 6 times, last edit by "-Vulture-" (Mar 28th 2023, 11:02pm)
-