• 05.11.2025, 15:26
  • Register
  • Login

  • You are not logged in.

 

Leakshield Setup Issues?

Dear visitor, welcome to Aqua Computer Forum. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

kfondren7

Newbie

Leakshield Setup Issues?

Tuesday, March 15th 2022, 7:49pm

I recently bought a combo d5/leakshield and have not been able to get the pressure above 60-80 mbar. My loop is airtight. I think the issue is the seal and or valve on the leakshield. I've tested the pump housing outside of the loop with two g1/4 threaded plugs on the inlet and outlet ports. Then ran the pressure test and it still did not rise above 60-80 mbar. Is there anything I can do to determine if the valve is the issue?

r3volt97

Junior Member

Wednesday, March 16th 2022, 3:49am

I'm in the same boat , i've checked every component down to the pump and there's still pressure going out ( i'm on 10/13 soft tubing tho ).

RBMDragon

Junior Member

Wednesday, March 16th 2022, 8:18am

You would be surprised how sensitive the Leakshield is.

I've had to test each step individually to find the cause of the leak.
It turned out that it was near the Leakshield itself. You have to make sure that the gasket is in properly, that the Leakshield isn't attached improperly (I turned it counter clockwise to ensure it was level in the thread) then I had to tighten it a lot.
I think this is merely due to the diameter.

For me, I carefully (first time building a water cooling loop) tested each part to narrow down where the air was leaking in.
Remember also to hold the Ultitube when attaching the Leakshield so as not to unscrew any other parts of the combo unit.

kfondren7

Newbie

Thursday, March 17th 2022, 5:01pm

Are you saying there is a gasket on top of your utilitube? I don't believe mine has one - I thought the gasket was on the leakshield - that might be my issue

kfondren7

Newbie

Thursday, March 17th 2022, 7:54pm

welp... found the gasket - definitely my fault - not sure why my brain thought - oh cool extra gasket when I installed the pump - but definitely working fine now.

knacker

Full Member

Friday, March 18th 2022, 3:09pm

sounds exactly the same issue I am having and there was defiantely no gasket in the box as I checked on more than one occasion.
is it possible to purchase a gasket/oring seperately then otherwise I only have a nice screened top to my ultitube :wacko:

r3volt97

Junior Member

Saturday, March 19th 2022, 9:33pm

The so called gasket is an actual o-ring ??

https://shop.aquacomputer.de/product_inf…roducts_id=2003


i have purchased the Ultitube pro 150 , i've installed the o-ring round the bottom pump then a bigger rubber gasket at the of the Ultitube and nothing for the top where Leakshield screwing in . Did i miss something ?

RBMDragon

Junior Member

Tuesday, March 22nd 2022, 7:56am

This; Replacement gasket for ULTITUBE reservoirs (aquacomputer.de)
is the actual gasket that came with the kit I bought.

In my loop, the D5 NEXT was already mounted on the ULTITUBE.

This post has been edited 1 times, last edit by "RBMDragon" (Mar 22nd 2022, 7:57am)

r3volt97

Junior Member

Wednesday, March 23rd 2022, 1:42am

Quoted from "RBMDragon"

This; Replacement gasket for ULTITUBE reservoirs (aquacomputer.de)
is the actual gasket that came with the kit I bought.

In my loop, the D5 NEXT was already mounted on the ULTITUBE.
Was it at the bottom of the tube ?

Taubenhaucher

God

Wednesday, March 23rd 2022, 7:36am

Quoted from "r3volt97"

Quoted from "RBMDragon"

This; Replacement gasket for ULTITUBE reservoirs (aquacomputer.de)
is the actual gasket that came with the kit I bought.

In my loop, the D5 NEXT was already mounted on the ULTITUBE.
Was it at the bottom of the tube ?
https://shop.aquacomputer.de/product_inf…roducts_id=3860
Es gibt keinen Ausweg, den ein Mensch nicht beschreitet, um die tatsächliche Arbeit des Denkens zu vermeiden.
Thomas Alva Edison (1847-1931), amerik. Erfinder

r3volt97

Junior Member

Thursday, March 24th 2022, 10:55pm

Quoted from "Taubenhaucher"

Quoted from "r3volt97"

Quoted from "RBMDragon"

This; Replacement gasket for ULTITUBE reservoirs (aquacomputer.de)
is the actual gasket that came with the kit I bought.

In my loop, the D5 NEXT was already mounted on the ULTITUBE.
Was it at the bottom of the tube ?
https://shop.aquacomputer.de/product_inf…roducts_id=3860
already having a filter , i have procut number 34122 at the bottom the one u first linked me to . I've looked at the Leakshield properly and there is room for a big o-ring . They only have sent one for the pump . Mine is still broken , even not mounted on - it's still showing 80-85 mBar on the display ..

Taubenhaucher

God

Friday, March 25th 2022, 7:37am

The Ultitube has 3 gaskets, the top one is this molded part , the bottom one is integrated with the filter and the pump has an O-ring.

Please correct me if I am wrong.
From the productpage:"At the bottom of the reservoir, an integrated stainless
steel mesh filter element effectively separates both particles and air
bubbles from the coolant. The mesh filter is integrated into a molded
rubber part and can be rinsed with tap water. The gasket between glass
tube and lid is also a molded rubber part, designed to be securely held
in the right position during fastening of the lid."
Es gibt keinen Ausweg, den ein Mensch nicht beschreitet, um die tatsächliche Arbeit des Denkens zu vermeiden.
Thomas Alva Edison (1847-1931), amerik. Erfinder

r3volt97

Junior Member

Friday, March 25th 2022, 8:35am

When i first installed my res i had it alright but because i unscrewed the lid so many times as i either did cable management or had to refill , i incorectly screwed it enough times to make me disassemble and look for a flaw . Found few stains ( from my Primo prep treatment ) on the threads on the bottom pump which looked very dry and i though the top gasket was supposed to be at the bottom . I had good and bad readings from the Leakshield before , afterwards only capping 80 to 90 so i guess i'd better get on it as soon my loop gets treated by the Primochill substance .

By the way , are they gonna truly provide us with consumables when needed ?

Taubenhaucher

God

Friday, March 25th 2022, 10:18am

Quoted

By the way , are they gonna truly provide us with consumables when needed ?
I do not understand the question.
Es gibt keinen Ausweg, den ein Mensch nicht beschreitet, um die tatsächliche Arbeit des Denkens zu vermeiden.
Thomas Alva Edison (1847-1931), amerik. Erfinder

Similar threads