• 01.10.2026, 03:52
  • S’inscrire
  • Connexion

  • Vous n’êtes pas connecté.

 

Aquaero 5 Pro- broken need help

Bonjour, visiteur, bienvenue sur les forums Aqua Computer Forum. Si c’est votre première visite, nous vous invitons à consulter l’Aide. Elle vous expliquera le fonctionnement de cette page. Pour avoir accès à toutes les fonctionnalités, vous devez vous inscrire. Pour cela, veuillez utiliser le formulaire d’enregistrement, ou bien lisez plus d’informations sur la procédure d’enregistrement. Si vous êtes déjà enregistré, veuillez vous connecter.

knacker

Full Member

Aquaero 5 Pro- broken need help

lundi 22 octobre 2012, 11:21

Just had a major flood and think that my AQ5 is kaput- it will only power one pump if connected via the adaptor but both pumps work if connected directly to a psu molex

Any way to check to see if it is broken or can I use the 3 pin fan connector from the adaptor to control the pump output as when connected to the psu, they only work at 100% which is v ery loud!



Help would be most gratefully received

Shoggy

Sven - Admin

lundi 22 octobre 2012, 12:54

If I got it right one fan channel seems to be dead?I would recommend only to connect a normal 3 pin fan and set a manual controller with 100% for this channel. If the fan does not work you can be pretty sure that something is damaged.

knacker

Full Member

lundi 22 octobre 2012, 13:22

Shoggy- thanks for reply.

I think that the whole unit is damaged unfortunatley- so will have to save for a new one

In the meantime, if I connect the pump molex to the psu molex and 3 pin fan connector from the pump's adaptor to a fan controller, will this allow me to control the pump speed like a fan until I can afford a new AP5?

Shoggy

Sven - Admin

lundi 22 octobre 2012, 14:27

I do not know which pump you are using but this should not work since the speed of the pump is regulated by its voltage.

By the way: if the main controller is damaged it can be exchanged with anew one which will be still much cheaper than a whole new device.

knacker

Full Member

lundi 22 octobre 2012, 14:47

Shoggy



Thanks for your suggestion of trying a different fan header- I removed the A 5P and tried hooking the pumps up to different headers and have found that header 2 does not work -

I now have 7 or 9 fans that I need to connect to just one fan header- might just have to use the Lamptron for that unless I can think of something else!

BorisTheSpider

Full Member

lundi 22 octobre 2012, 17:23

You could abandon the blown fan channel, and add a poweradjust to get another one back.

knacker

Full Member

lundi 22 octobre 2012, 17:30

Aye, that's an option but I will try using the lamptron hidden in the case until I can afford to get the poweradjust- presume just the basic one will suffice

knacker

Full Member

lundi 22 octobre 2012, 20:52

Just been running for most of the afternoon and now have to have the pumps direct to molex on psu otherwise i get random pump failures i.e. one will start one time then the other will start then both- not very happy at the moment but will look at more tomorrow ?( ;(

knacker

Full Member

mercredi 24 octobre 2012, 15:03

Well just been running since yesterday and still getting random issues- one time it all works, next start up one fan channel doesnt work, next reboot 2 controllers dont work

Just fed up with this so have decided to ditch the unit completely as it is not stable even though it means having to drain a loop and re order the loop

It could have been a good bit of kit but there are too many problems especially the software

Discussions similaires