The description says:
"The poweradjust 2 is a controller which was optimized for the use with a Laing DDC pump but you can also use it for other things with a constant load of up to 25W at 12V. The maximum surge current can go up to 48W so you have enough reserves for the massive starting current that some pumps or fans generate. A freely configurable startboost allows you to make sure that for example a pump has enough time to spin-up before it is getting slowed down by the controller. That feature also works if the speed or flow rate signal gets interrupted."
So this is a controller optimize for pump usage but it can be used to power fans as well.
Im looking to build a watercooling loop, actually two loops, and im looking to see how much fans can be powered with a single controller.
I'll be having 3x120.4 radiators (also from aqua computer as these copper babies seem to be the best on the market) and 1x120.2
Thats gonna be 14x120 fans in single comfiguration or 28 in push pull configuration.
Ideally i would want all to be controlled via software through a Aquaero 5 XT Controller
Controller has 3x3pin Power output Fan Header, and 1x4pin PWM Fan Header
THe Power adjust 2 has 1x3 Pin Fan Header
I learned that 6 of them could be connected through each other and then through aqua bus to Aqua aero XT
That would be 9x3 pin Power and 1x4pin fan Header.
1)Would it be ok if i were to use Y header to use one controller to connect to 2 Fans ?
2)How much higher can i go, can i use one controller to power 4 Fans ?
Using a 5,125 bay with 3 Power adjusts, that costs 35 euros each powering only 3 fans, seems like a bad ideea, when i can get for instance this 8 chanell Laptron controller, http://www.overclockers.com/lamptron-fc8…troller-review/, much cheaper
3)Can you list here the exact connectors the controller has and what can be done with each connector ?
4)Will there ever be another Version of power adjust optimizied for controlling fans only, say with 4x3 pin adapter or 4x4 pin PWM adapter ?
5)Will there ever be a water block for these adapters made ?
I would rather use a Power adjust so that i can controll everthing through aqua suite, so i need to know what exactly can be done with a single adapter.
I also want to know if going 6xPoweradjust makes sense or not, just for controlling fans. I need to know what else can one do with the unit.
I'll pretty much control everything else through aquaaero 5 XT, like temperatures, flow, etc (still need to figure out what the XT controller can really do).
6)Whats the difference betwen a 3 pin and 4 pin power controller ?

And i can use as many Y connectors as i need, right ?
As the math allows, right ?
Here, states that this noctua Fan has
Max. Input Current 0,05 A
Voltage 12 V
That means a total of 0,05x12=0.6 W ?
http://www.noctua.at/main.php?show=produ…42&lng=en&set=1
I heard that if the RPM are set to lower, "the resistance" is gonna get higher, and the temperature at the controller is gonna get higher, but will that use more Power ?
Or is this 0,6 W the maximum Power its gonna use ?
Does that mean that 24/0,6 = 40 Fans ?
Can i controll 40 such Fans with one single controller, is this accurate ?

Wouldnt it be better for fan controlling to use the multiswitch USB 1.41 ?
With 8 chanells and 1 Amper on each chanell,
we have the 140 mm noctua fan uses 0.8 Amper, 0.04 or 0.08
and 120 mm noctua fan uses 0.05 A
92 mm fan uses 0.11 A
80mm uses 0.11 A
60 mm 0.12 A
40m uses 0.05 A
That means that each chanell could power more Fans, if i understand that correctly

3x120.4 radiators push pull = 24 fans
1x120.2 radiator push pull = 4 fans
4x40mm case fans
120mx3 case fans
Thats a total of 35 fans.
I dont think it work alloneof aqua aero 5 XT, or would it ?
I would equip an aqua aero 5 and 3 power adjust, would that be enough ?

I got 3 5,25 bays at my disposal for controllers to power all fans,
One its for aquaero 5 XT, 2 for something else, ideally something that could also be controlled from the aqua suite.
2 Radiators will be with integrated punmp, 2 will be dual loop.
What would be the best setup ?
Should i be gettin an aqua aero and 6 Power adjust(2x5.25"), or one aqua aero and 2 LTs, or one auq aero one LT, 3 poweradjusts (1x5,25")

The radiators with pumps are these
1)120.2 http://shop.aquacomputer.de/product_info…roducts_id=2796
2)140.4 http://shop.aquacomputer.de/product_info…roducts_id=2889Powered by 4 pin molex, and the pump has a few more connections i think.

There are gonna be 2 more 120.4 dual loops
3)120.4 dual loop
4)120.4 dual loop
As i said i plan push pull on these babies
3x120.4 radiators push pull = 24 fans
1x120.2 radiator push pull = 4 fans
In total there are gonna be 28 radiator fans
5)4x40mm case fans

6)3x120mm case fans
I also saw this on the shop,
http://shop.aquacomputer.de/product_info…roducts_id=2363
What does it exactly do and how can it be used ?
It seems to increase the capability so that one can power more fans or something
And then there is this:
aquaero 4.00 powerbooster als nachträgliches Upgrade mit Umbauservice
Seems like something they will stick to the aqua aero. it says though that its compatible with the
Geräten der Serie 4.00 used
http://shop.aquacomputer.de/product_info…roducts_id=2347
What exactly is this by the way ?

Can anyone guide me on what would be the best way to power/drive the fans via aquaero 5 and and/or a combination of poweradjust2/aero xt, or any other required acceosorry from this firm. ?
I really want to get everything from one produces, it seems aqua computer shop has everything neded to make a complete watercooling system.

That is something i would be buying. Otherwise i think im gonna go with 6 Poweradjusts 2
I would be having 3x3pin connector on the controller and 6x3 pin connecttor on the power adjusts and 1 PWM output
THe question is how much can one Poweradjust power, is it 3 or 4 fans ?

The thing is it makes little sense to get 6 poweradjusts 2, just to controll fans, you would have 9x3 pin connectors and 1x4 pin connectors