Vous n’êtes pas connecté.
Bonjour, visiteur, bienvenue sur les forums Aqua Computer Forum. Si c’est votre première visite, nous vous invitons à consulter l’Aide. Elle vous expliquera le fonctionnement de cette page. Pour avoir accès à toutes les fonctionnalités, vous devez vous inscrire. Pour cela, veuillez utiliser le formulaire d’enregistrement, ou bien lisez plus d’informations sur la procédure d’enregistrement. Si vous êtes déjà enregistré, veuillez vous connecter.
Ce message a été modifié 3 fois. Dernière modification effectuée par "StephanWeber" (4 novembre 2017, 07:56)
Ce message a été modifié 3 fois. Dernière modification effectuée par "InfoSeeker" (4 novembre 2017, 17:06)
Ce message a été modifié 1 fois. Dernière modification effectuée par "InfoSeeker" (4 novembre 2017, 17:03)
O NoCitation
I appear to be having an issue with the aquabus.
The High Flow USB sensor does not list under aquaero>sensors tab (a6_sensors_flow.jpg)
The D5 USB pumps also do not list under the aquaero>Pumps tab (a6_pumps.jpg)
And the D5 USB Pumps are not available as a source for a preset controller (pumps_preset.jpg)
Citation
RESOLVED!
I had not followed Sebastian's instruction:
"When you make changes with aquabus devices you have to power of the pc completly (unplug the power cable)! "
After a full power reset the aquabus is working properly.
Ce message a été modifié 2 fois. Dernière modification effectuée par "Dundys" (4 novembre 2017, 17:11)
You mean PSU cableCitation
When you make changes with aquabus devices you have to power of the pc completly (unplug the power cable
Ce message a été modifié 4 fois. Dernière modification effectuée par "Dundys" (4 novembre 2017, 17:43)
I'm stupid I should have just left thing alone, everything in aquabus is gone Power cycle didn't do anything
I had every device connected via USB at initial setup so how come now everything is gone Helpppppp darn it
You mean PSU cableCitation
When you make changes with aquabus devices you have to power of the pc completly (unplug the power cable
Ce message a été modifié 1 fois. Dernière modification effectuée par "InfoSeeker" (4 novembre 2017, 17:48)
Ce message a été modifié 1 fois. Dernière modification effectuée par "Dundys" (4 novembre 2017, 17:58)
I switched the power off switch on PSU and removed cable as well. NO i didn't update anything other than Aquaeros firmware.
So I'm assuming I have to connect now USB to each device and aquaero and do the firmware update?
When I initially did all that it was about 2 years ago I honestly didn't want to bother anymore with this, Im ether getting to old or just getting brain farts, its getting more difficult and confusing.
Advice PLease?
Citation
If you use devices with the aquaero that are only connected via aquabus it is indispensable to connect such devices via USB to perform an update of the firmware, otherwise devices will no longer work with the aquaero or show a strange behavior.
Ce message a été modifié 2 fois. Dernière modification effectuée par "Dundys" (4 novembre 2017, 18:23)
Its nice when everything is functioning properly. Initially it took me forever to hook everything up but that was while ago I still had the energy fro that, something happen in between that now my energy level is so low I just don't feel like doing whole lot around my system I dont know maybe very busy lifestyle, to busy, but its all going to be OK once is done
So Do I connect now every PA3 and USB flow meter via USB to Aquaero or M/B?
I assume to aquaero and than update the firmware again with PA3 connected ?
Ce message a été modifié 2 fois. Dernière modification effectuée par "InfoSeeker" (4 novembre 2017, 18:33)
Ce message a été modifié 2 fois. Dernière modification effectuée par "Dundys" (4 novembre 2017, 19:29)
Ce message a été modifié 3 fois. Dernière modification effectuée par "Dundys" (4 novembre 2017, 23:53)
-