• 27.08.2026, 02:30
  • S’inscrire
  • Connexion

  • Vous n’êtes pas connecté.

 

Flow sensor high flow rates

Bonjour, visiteur, bienvenue sur les forums Aqua Computer Forum. Si c’est votre première visite, nous vous invitons à consulter l’Aide. Elle vous expliquera le fonctionnement de cette page. Pour avoir accès à toutes les fonctionnalités, vous devez vous inscrire. Pour cela, veuillez utiliser le formulaire d’enregistrement, ou bien lisez plus d’informations sur la procédure d’enregistrement. Si vous êtes déjà enregistré, veuillez vous connecter.

XXL24H

Junior Member

Flow sensor high flow rates

samedi 10 mars 2018, 18:53

I want veryfai may flow. Im using https://shop.aquacomputer.de/product_inf…roducts_id=2294
and Aq D5 pump on test loop, 30cm lenght and 10mm Id. Just with flow sensor and pump max i hawe 520 l/h. On minimum pomp rpm (1800) was165 l/h. Its ok? ?(

Shoggy

Sven - Admin

lundi 12 mars 2018, 12:10

520 l/h sounds unrealistic to me.

In a real loop of normal size you should get values between 150 - 200 l/h with that pump (full speed).

InfoSeeker

Senior Member

lundi 12 mars 2018, 15:56

I think his a test loop consists of the D5 pump, the high-flow sensor, & about 30cm of 10mm ID tubing to loop it back... no real pressure drop.
I've never run a test like that, so no data.

Syberon

Junior Member

mardi 13 mars 2018, 03:13

This is normal flow.
Some time ago i built the same test loop - SC600 pump (less powerfull then D5), reservoir and MPS Flow 400. In this loop flowmeter shows me it's maximum at 400l/h all the time. There is no restriction in this loop and therefore we have that big flow.

Ce message a été modifié 1 fois. Dernière modification effectuée par "Syberon" (13 mars 2018, 03:16)

XXL24H

Junior Member

mardi 13 mars 2018, 04:00

Thanks for answer :D On normal loop just with CPU block and 2 radiators (480 ocool xflow) i hawe about 132 max but im modifai flow sensor and remowe insaid resctrictions (use 10mm drilbit :). 8)

Shoggy

Sven - Admin

mardi 13 mars 2018, 09:19

Be aware that after such a modification the measured flow value won't be correct anymore because of the changed flow characteristics.

XXL24H

Junior Member

mardi 13 mars 2018, 21:40

Yes, i now. But i dril one new holl and tap it ,one is driled to 10mm and one is oryginał with resctriction and is pluged. When i hawe som time i trai calibrate it.

Jakusonfire

Full Member

lundi 19 mars 2018, 14:04

Those results look pretty close to Fast Fates testing.

http://www.overclock.net/forum/22568401-post7.html

He got up to around 2GPM with a single pump. The minimum is harder to tell because he used a tap to lower flow rather than lowering pump speed but it seems perfectly reasonable.

My loop, A CPU, GPU, MPS400 and dual rad loop runs at 4,6Lpm / 275L/h max flow with a single D5 USB. Older blocks were much more restrictive but these days over 200L/h is pretty common

Ce message a été modifié 2 fois. Dernière modification effectuée par "Jakusonfire" (19 mars 2018, 14:07)

Discussions similaires