• 23.08.2025, 10:49
  • S’inscrire
  • Connexion

  • Vous n’êtes pas connecté.

 

Aquabus / RPM signal cable 3 pins problems

XenoMorpH

Junior Member

Aquabus / RPM signal cable 3 pins problems

mardi 27 décembre 2016, 23:22

I created my own Aquabus / RPM signal cable. Used 2 old 3 pin female cables and soldered them togheter and sleeved them. Made 2 of them, but they don't seem to work?
Does anyone has an idea why they are not working? I reconnected the standard (pretty long) cables and the devices work with my Aquaero.... But not with those 2 hand-made cables :(

InfoSeeker

Senior Member

RE: Aquabus / RPM signal cable 3 pins problems

mercredi 28 décembre 2016, 13:51

Citation de "XenoMorpH"

I created my own Aquabus / RPM signal cable. Used 2 old 3 pin female cables and soldered them togheter and sleeved them. Made 2 of them, but they don't seem to work?
Does anyone has an idea why they are not working? I reconnected the standard (pretty long) cables and the devices work with my Aquaero.... But not with those 2 hand-made cables :(

My initial thought is an open, or you crossed the wires... can't be much else.

Curious, what are you connecting to the RPM signal port?

XenoMorpH

Junior Member

mercredi 28 décembre 2016, 16:11

This is how I created them:

20161121_152316b.jpg


After soldering them I used some heatshrink to protect the solder-joint

20161121_154410b.jpg


Then I single sleeved the cables.

20161121_163926b.jpg


I have no idea why it's not working.....

They are not for the RPM port, fior the aquabus-port...

Ce message a été modifié 1 fois. Dernière modification effectuée par "XenoMorpH" (28 décembre 2016, 16:13)

GTXJackBauer

Full Member

mercredi 28 décembre 2016, 22:36

What device were you using to connect them too since some devices need a 4-pin for power.

InfoSeeker

Senior Member

mercredi 28 décembre 2016, 23:11

Did you megger the cable with an ohm meter after sleeving to confirm continuity between the two plugs?

sebastian

Administrator

jeudi 29 décembre 2016, 07:12

Citation de "XenoMorpH"

Then I single sleeved the cables.

20161121_163926b.jpg
your cables are reversed! Compare the pin numbers on each side of the cable.

XenoMorpH

Junior Member

jeudi 29 décembre 2016, 11:42

Citation de "GTXJackBauer"

What device were you using to connect them too since some devices need a 4-pin for power.
Using a PowerAdjust 2 Ultra and a Farbwerk. They work with the standard 3pin cables....

Citation de "InfoSeeker"

Did you megger the cable with an ohm meter after sleeving to confirm continuity between the two plugs?
No I didn't, maybe that's what I could do.....

Citation de "sebastian"

Citation de "XenoMorpH"

Then I single sleeved the cables.

20161121_163926b.jpg
your cables are reversed! Compare the pin numbers on each side of the cable.

:S I think you are right :pinch:
Looking at this:

I now see that black and yellow are reversed. :whistling: Stupid me!
I'll try it out this evening Tnx!! :D

XenoMorpH

Junior Member

jeudi 29 décembre 2016, 22:24

And it worked!! But now my Farbwerk is not connecting anymore. Not even with the original cables. :thumbdown: ... I Updated and Rebooted through USB, restarted the pc and reconntec it, but a no go ;(

XenoMorpH

Junior Member

dimanche 8 janvier 2017, 14:17

Having a new problem...can not get any device work on the aquabus anymore. Not even with the standard cables.

I have 2 PowerAdjust 2 Ultra's, reset them to factory defaults, gave them a aquabus number (51 and 52).
Also the Farbwerk had a reset and gave it number (21).

The Aquaero had a factory reset, reconnected the devices one by one to the Aquaero, but they don't get detected. What's going on? :wacko:

XenoMorpH

Junior Member

mardi 10 janvier 2017, 22:42

No one? ;(

InfoSeeker

Senior Member

mardi 10 janvier 2017, 23:33

Your best bet may be to shoot tech support a message at support@aqua-computer.de

Discussions similaires