Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
I suspect your flow rate at 40% is less than 35 l/h.
Quote from the product description:
"The sensor delivers reliable readings over a wide range
of flow rates between 35 l/h and 1000 l/h (approximately 9 to 260 US
liquid gallons per hour) and is therefore perfectly suited for most
water cooling systems."
Dieser Beitrag wurde bereits 4 mal editiert, zuletzt von »anub1s21« (3. Mai 2021, 11:23)
I have 3x360 rads, one is quite restrictive (HWLabs GTS), 1 cpu block, 1 water filter and lots of 90 degree fittings & 90 degrees acrylic tubes.
The flow might be low but the temperatues are quite good, water temp is 30-31oC with pc on during browsing, with water temp ~27oC when the pc is shut down.
Btw nothing is cloged since I cleaned the cpu block thoroughly yesterday before re-assembling the loop.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »turgin« (12. Mai 2021, 03:45)
In the middle of integrating my new high flow NEXT into my loop and have a question regarding the power measurement and sensor placement. Can I place the NEXT after the rad and the external sensor before the rad or does the NEXT have to be on rad inlet? It sure would make my life easier if I can.
2 of the 360 rads are from HWLabs (GTS & SR2+) and 1 360 45mm alphacool X-flow. Cpu block is Heatkiller IV pro, no VGA block yet since I am still waiting my 3090 to be delivered since FebruaryI have 3x360 rads, one is quite restrictive (HWLabs GTS), 1 cpu block, 1 water filter and lots of 90 degree fittings & 90 degrees acrylic tubes.
The flow might be low but the temperatues are quite good, water temp is 30-31oC with pc on during browsing, with water temp ~27oC when the pc is shut down.
Btw nothing is cloged since I cleaned the cpu block thoroughly yesterday before re-assembling the loop.
I use 3 HWlabs radiators, two 360 crossflow and a 240 split flow, two waterblocks obviously and a ton of 90° fittings to slap an EK FLT pump against the glass of the case. at 40% i get 43L/h (66 at 50%, 100 at 60%, and maxing out at 260 at 100%).
So it's not really linear, and when the sensor was brand new, i sometimes had zero flow readings at low speed. Now that it has been spinning for a few weeks, i can run the pump at its slowest speed and it will give me 17L:min readings all day long.
It depends a lot on the brand of radiator you use, what waterblocks (some are more restrictive by a lot, if you use parallel/serial loop etc...) so everyone will have different values. Same stuff regarding tubing diameter.. you could use 16mm, in the end your fittings only have like a 9mm passage.
It would be more interesting to know what is the maximum flow your loop can achieve at full speed.
And tbh, there's lots of headroom, it's not worth it to stress about high flows unless you have several GPUs to cool.
I personally found no cooling benefit going beyond 100l/h on an OCed 3090. temps start shooting up below 40l/h and still, it only puts the GPU in the 50's °C
[SNIP]
So have three questions:
1) I know the sensor can be mounted vertically....but can the display orientation be rotated 90° ? It wouldn't look nice to have the info display sideways.
2) Anybody knows when there will be a new batch available ? I have been looking everyday (multiple times a day) for about a week, but nothing.
Off topic question:
3) Its not related to the sensor but....if i place an order with the sensor in it, eventhough its not available, will my order be shipped with the available items and the sensor shipped later as soon as it becomes available ? Or will the whole order be shipped only when the sensor is available. I am asking that question in order to know if i can get the rest of the stuff (Octo, Farbwerk,and w few other things) now and avoid paying twice for shipping.
Thank you for your answers.
-