• 05.05.2024, 05:30
  • Register
  • Login

  • You are not logged in.

 

Firmware Flash Stuck - Please Help!!

Dear visitor, welcome to Aqua Computer Forum. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.

bern43

Junior Member

Posts: 18

Firmware Flash Stuck - Please Help!!

Tuesday, November 13th 2012, 7:27pm

Just downloaded the new Aquasuite and tried to flash my firmware from 1025 to 1026. It keeps getting stuck at 95% and the screen on the Aquaero seems to be stuck on one of the sensor displays. Anybody have any ideas???

sebastian

Administrator

Posts: 10,520

Tuesday, November 13th 2012, 7:54pm

Power off your complete system. The update process is finished.

bern43

Junior Member

Posts: 18

Tuesday, November 13th 2012, 8:15pm

That did it. Thanks! One more quick question. Poweradjust 2. Does it no longer show up separate in the interface? I don't have anything connected to it yet, but it is wired to the Aquaero.

Namron

Full Member

Posts: 211

Tuesday, November 13th 2012, 8:51pm

Yep.. It does seem that the update has stopped just before the blue update guage reaches the end of the update window, But as Sebastian says, Close down the Aquasuite...Shut off the computer... & Then Turn complete PC off at the PSU.. Leave off for a few seconds so all the motherboard lights go out. Then switch the PC on again on the PSU & Boot the PC.. (this how it worked for me)

The newly updated Aquasuite should now be visible with all the New Updates e.t.c.. You will need to reset your settings as the update reset the unit to factory defaults..
No Problems to report & the update went smoothly for me. I havn't gone through it in full yet, Just setting up my Fans, Pumps & Curve controls at pressent, But all seems Good :)....

Nice one AC, Looking Good :thumbsup:
N.

LarryWill729

Full Member

Posts: 132

Tuesday, November 13th 2012, 10:21pm

Confirm the Firmware flash to 1026 problem. The progress bar stops at about 95%
Basically, cold boot the AQ5, and the reboot will show FW1025 and all is good.
Except you must go back and re do everything again!
AMD FX-8150 OctoCore O.C. 18% to 4.2 GHz on ASUS M5A99X EVO with 16 GB Corsair Dominator W. C. RAM, 2 nVIDIA Geforce 560TI W.C. in SLI, six Western Digital drives for a total of 4.07 TBytes, AquaComputer Aquero 5 Pro, AquaComputer D5 pump, Multiswitch USB, tubemeter and Kyros CPU block. Two coolant loops,CPU & SLI, MB, RAM and AQ5, with two flow meters. Running Windows 7 Professional 64, and using Open Hardware Monitor v0.5.1Beta Aquasuite B16 hardware temps.

Namron

Full Member

Posts: 211

Wednesday, November 14th 2012, 12:07am

I only had to update the once. Then after switching the PSU back on & re-booting the update was carried out straight away & updated to FW1026.. This was the case for both of my PC's Aquaero's.. Maybe I was just lucky :)

N.

This post has been edited 1 times, last edit by "Namron" (Nov 14th 2012, 12:09am)

Shoggy

Sven - Admin

Posts: 18,130

Wednesday, November 14th 2012, 3:01pm

There was a problem with the restart sequence at the end of the firmware update. The firmware update is already completed but the device does not start again. Just restart the system (on/off).

We uploaded RC2 this morning where this problem has been fixed.

Similar threads