New to Aquaero 6 XT - setup question. - English forum

New to Aquaero 6 XT - setup question.

Junior Member

New to Aquaero 6 XT - setup question.

Samstag, 13. Januar 2018, 17:06

Hi,

I had planned to move all my fans off the motherboard headers onto a Splitty9, but now I am wondering if it would be better to leave them all connected to the motherboard.

Will Aquaero control motherboard fan headers?

I have the following:

Gigabyte Aorus X399 Gaming 7 motherboard.
11 EK Vardar 140ER 500-2000 rpm fans (.35a each).
8 Fan Headers (1A each).
Sys1: 1 Fan
Sys2,3,4: 2 Fans each via Y splitter.
CPU & CPUOPT: 2 Fans each via Y splitter.
Sys5,6: EK DDC pumps.

The motherboard fan controller is less than desirable, but if Aquaero can manage the headers it might be better than using the Spitty9.

http://www.overclock.net/t/1636550/amd-r…0#post_26517986

Undermoose

Junior Member

Beiträge: 37

Samstag, 13. Januar 2018, 21:23

Zitat von »Undermoose«

Hi,

I had planned to move all my fans off the motherboard headers onto a Splitty9, but now I am wondering if it would be better to leave them all connected to the motherboard.

Will Aquaero control motherboard fan headers?

I have the following:

Gigabyte Aorus X399 Gaming 7 motherboard.
11 EK Vardar 140ER 500-2000 rpm fans (.35a each).
8 Fan Headers (1A each).
Sys1: 1 Fan
Sys2,3,4: 2 Fans each via Y splitter.
CPU & CPUOPT: 2 Fans each via Y splitter.
Sys5,6: EK DDC pumps.

The motherboard fan controller is less than desirable, but if Aquaero can manage the headers it might be better than using the Spitty9.

http://www.overclock.net/t/1636550/amd-r…0#post_26517986

I guess I'll figure out if AQ6 can control motherboard headers soon enough.

I think what I can do is:

4 radiator fans to FAN1 on AQ6 (1.4a max total)
4 positive pressure side fans to FAN2 on AQ6 (1.4a max total)
1 rear exit fan & 2 front intake fans to FAN3 on AQ6 (1.05a max total)
2 EK DDC to FAN4 on AQ6 (signal only, molex power)

InfoSeeker

Senior Member

Beiträge: 1 759

Samstag, 13. Januar 2018, 23:05

I do not believe the aquaero can control anything on the motherboard, other than perhaps power down.

Undermoose

Junior Member

Beiträge: 37

Thank you for the reply

Sonntag, 14. Januar 2018, 01:44

Hi,

Thanks for the reply.

I think I'm going to go with my 4 fan header config and control fans by zone.

1. Radiator
2. Side positive pressure
3. Front intake + Rear exit.
4. DDC pump signal.

Just got back from MIcrocenter with some extra y splitters

XXL24H

Junior Member

Beiträge: 12

Samstag, 10. März 2018, 17:17

New to Aquaero 6 XT - setup question.

New to Aquaero 6 XT - setup question.

Zitat von »Undermoose«

Thank you for the reply

Ähnliche Themen