Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
hawli
unregistriert
Make sure the cable is connected proper way on both sides(there are two ways of connecting the cable). Also make sure you connect the cable on the top row on NZXT device(all five pins). It's likely the issue of NZXT unit, NZXT device is not built that well, I've seen people who's unit have completely melted.Hi, I'm using aquaero 6. As there's not enought usb ports in my
mainboard (asus crosshair VI hero) I am using nzxt internat USB HUB. The
aquaero is detected in devices manager but aquasuite does not detect
it. It works when connected without usb hub. Every other devices are
working fine when connected to hub. I'm thinking maybe that a software
failure? Any ideas how to solve this?
The new one, since they melted the housing of the USB hub.
Are you referring to their older gen. USB hub and not their newer redesigned ones?
Regardless, I also agree on grabbing a HUBBY7 for all your needs.
I knew a bad batch of the older ones a while back were frying some peoples gear, even some AQ's I believe but thought they would have fixed any issues with the new redesig
Dieser Beitrag wurde bereits 4 mal editiert, zuletzt von »Undesirable« (25. Februar 2018, 00:57)
Something might be wrong with the Aquaero then.
I would test it once more with the new MB and go from there.
Dieser Beitrag wurde bereits 2 mal editiert, zuletzt von »Undesirable« (25. Februar 2018, 20:16)
Double check that the cable is in the correct order at both ends. Some of the wires use BB--R, where others are R--BB. There only one or two that are 1:1 at both ends. If incorrectly done it could create voltage issues and possibly destroying the device. Also check your Motherboard manual to make sure it's lining up as well.This thread is more confirmation that the Aquero isn't detected with
ASUS Crosshair VI & USB hubs. I have an older thread about it here: Aquaero 6 Not Detected with Hubby 7
The above thread includes the usage of an AquaComputer Hubby, so that appears to rule out the hub type making a difference.
It is essential that some form of USB hub is used with the Crosshair VI,
as it only has a single USB 2.0 header. So if the Aquaero is plugged in
without a hub, you cannot have a USB 2.0 front panel connector
installed.
Can AquaComputer please test Aquaero compatibility with USB hubs and
specifically the Crosshair VI motherboard? My AquaStream XT pump WAS
able to connect to the Hubby, but the Aquaero would NOT, and I tested
them both in USB and SATA power mode.
I have since upgraded to Threadripper with a new motherboard that has
two USB 2.0 headers, so I am no longer affected and can no longer test
myself.
Zitat
I believe the "5th" pin is normally reserved for the cable shield wrap and is not directly related to data transmission.
Strange! its been a while and no support from AQ at least in here, its been very quiet let alone no word why they discontinued their USB D5if they did they should announce something in regards
Zitat
Where did you hear that they'd been discontinued?
No doubt AquaComputer would respond to a support ticket, but be prepared to be asked if your USB cables are attached correctly for the billionth time.
Someone have been told that .........post # 6. How much true is that I'm not sureZitat
Dieser Beitrag wurde bereits 3 mal editiert, zuletzt von »Dundys« (27. Februar 2018, 23:40)
ms something niggles in the back of my mind about dissimilar grounds for the 12/5 volt plugs in
Can, also, confirm this with Hubby7 (or with NZXT ) USB Hub on the ASUS C6H Board : MPS High Flow is detected through HUB in aquasuite but not the aquaero (6XT or 6LT with last firmware). When connected on the motherboard USB Header, all is fineWell at least you're trying to help us. I'm almost certain it's an incompatibility with Crosshair 6 motherboards and USB hubs + some AquaComputer devices.
4 people have the same issue with this motherboard (well, 3 confirmed in this thread and 1 unknown motherboard + USB hub).
-