Sie sind nicht angemeldet.
Two water flow sensors (one to Flow header, other to Fan Header 1 converted to Flow), ........ I did upgrade the firmware of aquaero when installed Aquasuite, could that be one reason for this behaviour? How can i rollback the firmware? The actual firmware is 2011.
Oh, really? Didn't knew that. Thanks for the heads-up!Two water flow sensors (one to Flow header, other to Fan Header 1 converted to Flow), ........ I did upgrade the firmware of aquaero when installed Aquasuite, could that be one reason for this behaviour? How can i rollback the firmware? The actual firmware is 2011.
The second flow meter has to be connected to the "aquabus low" port since firmware 2010.
There is no ppssibility to downgrade the firmware.
Zitat
4.6. Connector “aquabus low speed/high speed”
Connectors for communication with other devices from Aqua Computer. The
aquaero 5/6 features one „low speed“ (aquabus 1) and one „high speed“
(aquabus 2) port.
Products compatible to the “low speed” port:
● Port disabled since firmware version 2000, currently no supported devices.
Zitat
4.4. Connector “PWM 1/2”
Pulse width modulated 12 V outputs, maximum current load 1 A, carrier frequency
15 kHz. Suitable for example for 12 V LEDs, not compatible with
PWM fans or pumps.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »InfoSeeker« (28. Februar 2018, 17:33)
The auqabus low port is disabled and does nothing since the 2000 firmware update.
Snippet below quoted from page 10 of the current aquaero manual:
Zitat
4.6. Connector “aquabus low speed/high speed”
Connectors for communication with other devices from Aqua Computer. The
aquaero 5/6 features one „low speed“ (aquabus 1) and one „high speed“
(aquabus 2) port.
Products compatible to the “low speed” port:
● Port disabled since firmware version 2000, currently no supported devices.
The aquasuite has received an update. ....
Changelog for aquaero 5 and 6
Also new is that we moved the option to connect a second flow sensor from fan port 1 to the aquabus lowspeed port which had no function lately. This way fan port 1 can be still used for other stuff when connecting a second flow sensor.
- New: a second flow sensor will be connected to the aquabus lowspeed port now
..
Yes, they are the two pin headers and yes, i know about the PWM fan incompatibility (which is weird as the headers are labelled "PWM", a little explanation about what is PWM can be found here ). I'm using it purely for its electricity properties. The set of fans connected there are simple two wire fans. Reduce voltage, reduces the speed, straight simple as that, just like connecting any two wire LED. However, if that thing about "aquabus low" is true i won't need to connect them onto "Power Output" any more, leaving it available for the 12v LEDs as intended.
If the "Power Outputs" 1 & 2 you refer to are the 2-pin PWM ports, they are NOT for fans!
Snippet below quoted from page 9 of the current aquaero manual:
Zitat
4.4. Connector “PWM 1/2”
Pulse width modulated 12 V outputs, maximum current load 1 A, carrier frequency
15 kHz. Suitable for example for 12 V LEDs, not compatible with
PWM fans or pumps.
You may be a candidate for a poweradjust 3 USB, standard or a poweradjust 3 USB, ultra.
The flow meter connected to aquabus low will not appear on the aquabus tab in the aquasuite. If it works on the flow port on the aquaero then it has to work on the aquabus low port also. Check the tab "aquaero" > "Sensors" > "Flow sensors"Have done a reset to aquaero and made a new information page with "flow2" selected, but can't get any reading nor any device on "aquabus devices" settings, which leads to what InfoSeeker said. That or the flow sensor now isn't compatible with this new layout (it still works on "flow1").
That is not the answer, because you will get update notifications when your aquasuite is too old...Guess i shouldn't have updated this thing as it brought me more problems than solutions...
-