pump starts .... and stops ... aquabus error light

Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.

maverick72

Junior Member

Beiträge: 12

pump starts .... and stops ... aquabus error light

Samstag, 19. Februar 2005, 18:26

Need help bleeding my systems ... got all the leaks .. filled my reservoir ... started the pump ... loop looks good ... BUT pump stop for a second ... error light comes on ... pump goes back on for couple of seconds.

What i'm I missing?

edit: I got the 3 red blink which is

pumpe nimmt keinen strom auf oder ist nicht angeschlossen

Which according to babelfish ...

pump takes up no river or is not not attached

That really isn't helping

Shoggy

Sven - Admin

Beiträge: 18 130

Re: pump starts .... and stops ... aquabus error l

Samstag, 19. Februar 2005, 18:36

Maybe the jumper of the deaeration-mode is set. It's the one on the right.

1x flash impulse of the red led means that your psu doesn't deliver enough power (below tolerance of 12V).

maverick72

Junior Member

Beiträge: 12

Re: pump starts .... and stops ... aquabus error l

Samstag, 19. Februar 2005, 18:38

Zitat von »Shoggy«

Maybe the jumper of the deaeration-mode is set. It's the one on the right.

1x flash impulse of the red led means that your psu doesn't deliver enough power (below tolerance of 12V).

The psu is a antec 420 true power which should be alright.

What does that jumper do and more important ... where should it be

... thanks alot for your help.

Shoggy

Sven - Admin

Beiträge: 18 130

Re: pump starts .... and stops ... aquabus error l

Samstag, 19. Februar 2005, 18:42

If the jumper is set the pump will run for some seconds, will stop, run, stop and so on ;D
This mode is used to get rid of air within the components.

Without the jumper the pump is runnig in a normal way.

back_orifice

God

Beiträge: 2 878

Re: pump starts .... and stops ... aquabus error l

Samstag, 19. Februar 2005, 19:12

But this all just works when u have the AS... ;D ;D

maverick72

Junior Member

Beiträge: 12

Re: pump starts .... and stops ... aquabus error l

Samstag, 19. Februar 2005, 19:55

Zitat von »back_orifice«

But this all just works when u have the AS... ;D ;D

All good ... thx guys

aviddigi

Junior Member

Beiträge: 25

Re: pump starts .... and stops ... aquabus error l

Dienstag, 22. Februar 2005, 03:56

Did you figure out the problem?, i have been fighting with my AS and now it is giving me 3 red flashes. Tried to email AC for the past week about warranty info or help with no response. All the jumpers are where they should be set up the same as my current working setup.
Thanks

Halk

Junior Member

Beiträge: 55

Re: pump starts .... and stops ... aquabus error l

Donnerstag, 3. März 2005, 20:43

According to the manual, 3 red flashes means the pump is not receiving power or is not connected correctly.

You haven't accidentally undervolted it?

There's a link to the manual for it in English somewhere on the site, the manual is well written too.

Shoggy

Sven - Admin

Beiträge: 18 130

Re: pump starts .... and stops ... aquabus error l

Donnerstag, 3. März 2005, 21:03

FYI: the "problem" was the deaeration-mode