Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
Hello everyone,
I am new to the AquaComputer system. I have been building
custom pc for a while. I have an EK dual D5 pump housing that I would like to control
with the Aquasuite software. I would like to know if 2 none PWM pumps can be
controlled and if so, what will I need to do just that? I currently have a cuplex
kryos NEXT with VISION AM4 WB, & AquaSuite that it.
Thank you for your cooperation
If the pumps are non PWM and are the Vario type then they cannot be controlled with Aquasuite.Hello everyone,
I am new to the AquaComputer system. I have been building
custom pc for a while. I have an EK dual D5 pump housing that I would like to control
with the Aquasuite software. I would like to know if 2 none PWM pumps can be
controlled and if so, what will I need to do just that? I currently have a cuplex
kryos NEXT with VISION AM4 WB, & AquaSuite that it.
Thank you for your cooperation
The pumps are Swiftech MCP655.
Link: https://www.newegg.com/swiftech-mcp655-1…N82E16835108082
I have attached a manual PDF of the pumps.
I was looking at that, but these pumps only have the power Molex
(12VDC x 2 = 24VDC) how the Aquaero 6 LT would connect to the pumps?
Thank you for the suggestion, I can do this.I was looking at that, but these pumps only have the power Molex
(12VDC x 2 = 24VDC) how the Aquaero 6 LT would connect to the pumps?
I may get flamed for suggesting this, but if you have the pumps and want to use them, this is an option:
The pumps are rated at 2A
- remove the 4-pin molex plugs from the pump's power lead
- replace with a fan style plug (3 or 4 pin), connecting to the +12V & ground pins
- plug each of the two pumps into it's own fan port on the aquaero 6
- set the vario knob on the back of the pumps to 5 (full power)
- in the aquasuite set the fan port to "Power controlled" [attach]7479[/attach]
- I recommend you install a Passive heat sink for aquaero 6
The aquaero 6 fan port is rated to 2.5 amps, so you would be running at 80% capacity.
CAVEAT: all modifications are at your own risk... if you are not familiar/comfortable with this process, do NOT attempt!
I was looking at that, but these pumps only have the power Molex
(12VDC x 2 = 24VDC) how the Aquaero 6 LT would connect to the pumps?
I may get flamed for suggesting this, but if you have the pumps and want to use them, this is an option:
The pumps are rated at 2A
- remove the 4-pin molex plugs from the pump's power lead
- replace with a fan style plug (3 or 4 pin), connecting to the +12V & ground pins
- plug each of the two pumps into it's own fan port on the aquaero 6
- set the vario knob on the back of the pumps to 5 (full power)
- in the aquasuite set the fan port to "Power controlled" [attach]7479[/attach]
- I recommend you install a Passive heat sink for aquaero 6
The aquaero 6 fan port is rated to 2.5 amps, so you would be running at 80% capacity.
CAVEAT: all modifications are at your own risk... if you are not familiar/comfortable with this process, do NOT attempt!
From what I can see and with everyone's input as long as I have Red wire with Red wire & Black wire with Black wire I should be good.I was looking at that, but these pumps only have the power Molex
(12VDC x 2 = 24VDC) how the Aquaero 6 LT would connect to the pumps?
I may get flamed for suggesting this, but if you have the pumps and want to use them, this is an option:
The pumps are rated at 2A
- remove the 4-pin molex plugs from the pump's power lead
- replace with a fan style plug (3 or 4 pin), connecting to the +12V & ground pins
- plug each of the two pumps into it's own fan port on the aquaero 6
- set the vario knob on the back of the pumps to 5 (full power)
- in the aquasuite set the fan port to "Power controlled" [attach]7479[/attach]
- I recommend you install a Passive heat sink for aquaero 6
The aquaero 6 fan port is rated to 2.5 amps, so you would be running at 80% capacity.
CAVEAT: all modifications are at your own risk... if you are not familiar/comfortable with this process, do NOT attempt!
I thought about that but didn't want to be liable for damages if possible. lol
I thought about that but didn't want to be liable for damages if possible. lol
-