Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »eaonflux« (9. Januar 2019, 13:49)
It looks like you have some feature overlap. The Aquaero will probably do all the control duties, whereas the control capabilities of the pump and flow sensor will go unused.
There's a "dumber" version of the flow sensor, and a "smarter" one. You have the smarter one, which is (I think) overkill if you also have the Aquaero.
but i can use all feautures from these devices with the Aquero? except if i dont connect the pump with usb i cant update firmware?
sorry i just want to be sure if everything would work over the Aquero
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »boli« (9. Januar 2019, 15:51)
you can try it.by the way can i chain this with the hubby7 due that i need 1 usb connection more?
you can try it.by the way can i chain this with the hubby7 due that i need 1 usb connection more?
in theory, the usb protocol allows you to chain a maximum of 5 usb hubs.
problems can be the power consumption of the connected usb devices, incompatibilities between the usb hubs and data transfer speed problems.
if the power consumption of all connected devices together exceed 500mA (=2.5 Watts), some devices will be dropped and/or wont function properly, causing problems.
the hubby7 is a usb 2.0 hub, so the transfer speeds are slow.
i dont know the usb speed of the hub in your picture. you should connect the faster hub to your mainboard, and the slower hub into the faster hub.
if chaining the usb hubs it does not work, you may need to buy a pci express to usb card. (depending on the available connections on your mainboard.)
A firmware update of the pump is sometimes necessary if you update the aquasuite software.
for this you have to connect the pump to an usb port and do the firmware update. after the update is done you can disconnect the pump from the usb again.
if you dont update the firmware, the pump can no longer be controlled with aquabus until the firmware update is done.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »eaonflux« (9. Januar 2019, 19:02)
i am going to connect everything like some explainend in this thread. the main things is that i know how i can/must connect them without causing hardware damage
but i can use all feautures from these devices with the Aquero? except if i dont connect the pump with usb i cant update firmware?
sorry i just want to be sure if everything would work over the Aquero
I assume you probably can, but I don't know unfortunately (I only got my own first Aquaero yesterday, and my other devices don't have any controller functions: a simple PWM pump, the simpler version of your flow sensor, several temperature sensors).
Until someone with more experience replies, you'll probably have to rely on the rather informative product pages and manuals.
Dieser Beitrag wurde bereits 2 mal editiert, zuletzt von »eaonflux« (9. Januar 2019, 19:06)
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »eaonflux« (24. Januar 2019, 00:00)
-