• 13.10.2025, 22:09
  • S’inscrire
  • Connexion

  • Vous n’êtes pas connecté.

 

New: aquasuite 2017-3.2

InfoSeeker

Senior Member

jeudi 12 avril 2018, 01:40

Citation

Dear all

My device update software and firmware after

Not connected MPS

please help me

Thanks All
alexchan0829 has attached the following files:

MPS appears connected by aquabus.

MPS appears not connected by USB.
Are you using a USB hub?

Ce message a été modifié 1 fois. Dernière modification effectuée par "InfoSeeker" (12 avril 2018, 01:42)

alexchan0829

Newbie

jeudi 12 avril 2018, 16:38

Yes I have used USB hub

InfoSeeker

Senior Member

vendredi 13 avril 2018, 00:14

Sometimes a USB hub introduces a problem.
It may be useful to move one of the MPS unit USB cables from the hub and connect it direct to a motherboard USB port to see if it shows that way.

alexchan0829

Newbie

vendredi 13 avril 2018, 14:14

感謝您的幫助和回复

InfoSeeker

Senior Member

vendredi 13 avril 2018, 14:29

Citation de "alexchan0829"

感謝您的幫助和回复
"Thanks for your help and reply"

You are welcome, hope it helped.

annihilation

Newbie

vendredi 11 mai 2018, 14:58

I have one of these flow sensors: https://shop.aquacomputer.de/product_inf…roducts_id=2294

How do I go about getting this updated? It is currently showing up under Aquabus but says "The device has no USB connection to is not recognized by the system" and then Remove device from aquasuite.

Any ideas?

GTXJackBauer

Full Member

vendredi 11 mai 2018, 16:20

Citation de "annihilation"

I have one of these flow sensors: https://shop.aquacomputer.de/product_inf…roducts_id=2294

How do I go about getting this updated? It is currently showing up under Aquabus but says "The device has no USB connection to is not recognized by the system" and then Remove device from aquasuite.

Any ideas?


There is a proprietary cable that you need to purchase since it's sold separately (unfortunately) and plug it into the Flow Header behind the AQ. Once you've done that, you can check and is if it's working under the Aquaero tab ---> Sensors tab ---> Flow Sensors. Once there, you should be able to choose your flow meter.

This particular flow meter doesn't need any firmware updates. It's basically a plug n play flow meter. That's not to be said about the other flow meters they sell that need a Aquabus or USB connection which then do need to be updated via firmware.

Ce message a été modifié 1 fois. Dernière modification effectuée par "GTXJackBauer" (11 mai 2018, 16:22)

annihilation

Newbie

vendredi 11 mai 2018, 16:27

Interesting. It stopped working since the update which is why I was asking. I will check the connections.

wpuser

Senior Member

lundi 14 mai 2018, 15:48

Citation de "annihilation"

I have one of these flow sensors: https://shop.aquacomputer.de/product_inf…roducts_id=2294

How do I go about getting this updated? It is currently showing up under Aquabus but says "The device has no USB connection to is not recognized by the system" and then Remove device from aquasuite.

Any ideas?


Are you sure the linked one is really your device?

The device in your link has no aquabus and no firmware. It cannot be updated.

Ce message a été modifié 1 fois. Dernière modification effectuée par "wpuser" (14 mai 2018, 15:49)

CoAff

Junior Member

jeudi 24 mai 2018, 02:08

Citation de "wpuser"

Citation de "annihilation"

I have one of these flow sensors: https://shop.aquacomputer.de/product_inf…roducts_id=2294

How do I go about getting this updated? It is currently showing up under Aquabus but says "The device has no USB connection to is not recognized by the system" and then Remove device from aquasuite.

Any ideas?


Are you sure the linked one is really your device?

The device in your link has no aquabus and no firmware. It cannot be updated.
The linked device uses this: https://shop.aquacomputer.de/product_inf…nu67405to0tgogk to communicate.

nhorn1983

Non enregistré

jeudi 7 juin 2018, 13:22

is it possible to get an update on the software on the kryos kuplex block. i just installed my ryzen 2700x on an asus strix x470 gaming-f last night and the temp sensors are showing close to 100c this has to be a software bug as it was reading correctly the other day with an asrock x370 board. thank you

Ce message a été modifié 1 fois. Dernière modification effectuée par "nhorn1983" (7 juin 2018, 17:30)

Shoggy

Sven - Admin

jeudi 14 juin 2018, 15:03

You can try to reset the device back to the factory defaults but I doubt that this is a software related problem. It is much more likely that the temperature sensor got damaged by installing the CPU again. The sensor is very sensitive to pressure and will show weird values when it gets damaged.

What is the exact variant of the block that you have? Maybe you can exchange it yourself.

Discussions similaires