20.08.2025, 06:44
Sprache ändern
Registrieren
Anmelden
Sie sind nicht angemeldet.
bcikota
Full Member
Donnerstag, 12. Januar 2012, 16:27
Hi Equinediver,
Had the same problem. I fixed it by re-installing the Aquasuite after the firmware update. Did not uninstall first, just re-installed over the old one. After that it works fine.
Just to test, I flashed the firmware again and had the same problem. Re-install helped again.
Kind regards,
Boris.
Had the same problem. I fixed it by re-installing the Aquasuite after the firmware update. Did not uninstall first, just re-installed over the old one. After that it works fine.
Just to test, I flashed the firmware again and had the same problem. Re-install helped again.
Kind regards,
Boris.
Equinediver
Junior Member
Freitag, 13. Januar 2012, 02:21
Thanks Boris, re-installing got it working
However, in my case it seemed to be importing my saved settings file that made it crash. This is a SS of the error message
http://imgur.com/xGd6s
However, in my case it seemed to be importing my saved settings file that made it crash. This is a SS of the error message
http://imgur.com/xGd6s
bcikota
Full Member
Freitag, 13. Januar 2012, 09:38
Hi TheSmoker,
Yup, there is a new version of software sensors, alpha 2 as they call it.
You can find it at the same link as before:
http://aquacomputer.de/tl_files/aquacomp…uterService.zip
They just say they fixed a couple of bugs in this one, without more details.
Also, according to Sebastian from Aqua computer, they are not planning to add more then 4 sensors in the near future.
Kind regards,
Boris.
Yup, there is a new version of software sensors, alpha 2 as they call it.
You can find it at the same link as before:
http://aquacomputer.de/tl_files/aquacomp…uterService.zip
They just say they fixed a couple of bugs in this one, without more details.
Also, according to Sebastian from Aqua computer, they are not planning to add more then 4 sensors in the near future.
Kind regards,
Boris.
franknitty69
Junior Member
Mittwoch, 18. Januar 2012, 03:56
i've never had any issues with aquasuite until this latest version.
software install went fine but i had couldn't install the firmware. i tried a soft reset (jumper sensor
and that didn't work. so i tried recovery mode (jumper sensor 5- and that worked.
next my profiles wouldn't import stating that they were incompatible. so now i had to go and set everything back up.
then i tried the alarms. just clicking on that page causes aquasuite to crash. and after the crash, aquasuite resets all pages and will not control fans. i had to soft reset the aquero and re-install aquasuite.
great job on this release guys.
software install went fine but i had couldn't install the firmware. i tried a soft reset (jumper sensor
and that didn't work. so i tried recovery mode (jumper sensor 5- and that worked.next my profiles wouldn't import stating that they were incompatible. so now i had to go and set everything back up.
then i tried the alarms. just clicking on that page causes aquasuite to crash. and after the crash, aquasuite resets all pages and will not control fans. i had to soft reset the aquero and re-install aquasuite.
great job on this release guys.
sebastian
Administrator
Donnerstag, 19. Januar 2012, 08:51
Reflash the firmware and dont load your old profile.Everything is working fine with Beta 11, except the Alarm control crashes when I try to access the page.
can you send us the error message to: info@aqua-computer.de
Where is my problem? Hope, not in my DNA... ;)
Freitag, 20. Januar 2012, 00:51
Well, I am a new user of Aquaero 5 PRO. Got it, did a draft hardware install (all sensors and USB wire) and wanted to use AquaSuite 2012.
Prerequisites
Windows 7 Pro 64 bit
Logged as Administrator
.NET 4.0 installed and completely upgraded to the most recent state via Windows Update
Installation
Went OK. No errors, no warnings. Just in case, I reboot computer.
Problem
When I start AquaSuite, I get boring picture like
If I try to go to overview pages, choose Import and select "aquaero5_default.page" file, I get the below picture on my screen
I am not very new in IT and PC cooling, but this is my very first experience with AquaComputer products and I don't understand what went wrong.
PS. By the way, after I've got this negative result, I also played with previous version of the software. It gets installed and worked fine. I just did not have any AC components designed for this version...
Prerequisites
Windows 7 Pro 64 bit
Logged as Administrator
.NET 4.0 installed and completely upgraded to the most recent state via Windows Update
Installation
Went OK. No errors, no warnings. Just in case, I reboot computer.
Problem
When I start AquaSuite, I get boring picture like
If I try to go to overview pages, choose Import and select "aquaero5_default.page" file, I get the below picture on my screen
I am not very new in IT and PC cooling, but this is my very first experience with AquaComputer products and I don't understand what went wrong.
PS. By the way, after I've got this negative result, I also played with previous version of the software. It gets installed and worked fine. I just did not have any AC components designed for this version...
Ähnliche Themen
-
Überwachung und Steuerung »-
aquaero - FAQ und weitere Informationen
(11. April 2011, 09:06)
-
- Wasserkühlung »
-
aquasuite 2012 Beta und Firmware 1024 für aquaero 5 - Beta 15
(20. Mai 2011, 18:26)
-
- Überwachung und Steuerung »
-
Entwicklungsstand Aquasuite 2012
(12. Oktober 2011, 17:53)