Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
If you do not use the aquabus connection to the aquaero, you do not need to set the aquabus addresses for the pumps.Zitat
How do I assign the 2 ports for the pumps?
Do I have to manually assign the ports for the two pumps in the aquasuite or are they automatically picked up if you connect the pumps/ Aquero via USB?
Setting the addresses can be done with only the USB connection, the 4-pin Molex power connection is not required to set the aquabus address.Zitat
Do the pumps have to be connected to the Molex power supply to sort out the port assignment or will the power in the USB connection be enough for this assignment?
If you do not use the aquabus connection to the aquaero, you do not need to set the aquabus addresses for the pumps.Zitat
How do I assign the 2 ports for the pumps?
Do I have to manually assign the ports for the two pumps in the aquasuite or are they automatically picked up if you connect the pumps/ Aquero via USB?
You set the aquabus addresses via the USB connection.
Addresses 10 and 11 are available (per section 15.4 of the manual), so one can remain at the default address and the 2nd needs to be changed.
Going from memory, you click on one of the aquastream tabs on the left, then click the system tab, and you should see where you can set the address.
Setting the addresses can be done with only the USB connection, the 4-pin Molex power connection is not required to set the aquabus address.Zitat
Do the pumps have to be connected to the Molex power supply to sort out the port assignment or will the power in the USB connection be enough for this assignment?
Zitat
Just one more thing, is it OK to run all of the aqua computer parts I have got just with USB connections only and not connect any of the Aquabus terminals together?
Thanks again, that makes sense and I understand.Zitat
Just one more thing, is it OK to run all of the aqua computer parts I have got just with USB connections only and not connect any of the Aquabus terminals together?
This is an oft asked question. I will try to explain the relationship of the two connections.
The USB connection allows you to setup the aquacomputer device (i.e. set addresses), update firmware and such.
The aquabus connection is used for control and monitoring of the device through the aquaero, where you can set control curves, etc., to control the device's performance according to system parameters (i.e. control fan speed according to water temperature).
After initial setup of your devices, you could remove the USB connection except some devices, like the flow sensor, does self-calibration when the system is off, which requires the 5v from USB.
On my machine I have both USB and aquabus connected... they are not mutually exclusive, but complement each other.
I know of, but have no familiarity with farbwerk, but perhaps it provides a solution? (aquabus & Bluetooth versions are mutually exclusive, one cannot do the other)
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »InfoSeeker« (19. März 2015, 20:33)
Thank you again, I appreciate your replies.I have an aquaduct 360 mark V which has an aquaero 5 XT, and my gigant 1680 has an aquaero 6 pro, and I see both in aquasuite and can control both independently.
You should see 2 auqaero tabs on the left in aquasuite, and both should be controlled independently.
Edit: Just as you can with MPS devices, you can assign a personal title to each aquaero (i.e. "CPU Loop" & "GPU Loop") for ease of identifying which does what.
Zitat
PS 2.04m of radiators, that's impressive I only have 1.82m
-