• 24.07.2025, 07:24
  • Registrieren
  • Anmelden

  • Sie sind nicht angemeldet.

 

fan speeds by controller

Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.

garyd52

Junior Member

fan speeds by controller

Mittwoch, 22. Juli 2015, 18:20

Hi , I have an Aquaero 6 which I use to control 2 laing ddc's and an aquastream ultra I have 2 rads with 4 fans each in push pull and 4 temp sensors plus the one built into the aquastream the fans use a Y splitter I have tried to set up a fan curve to ramp up fan speeds with temperature and have tried using all the temp sensors plus the aquastream one as the data source, I want the fans to run at maximum speed once 40 degrees is reached and have used the auto setup to set the fan curve but it does'nt work I use occt to stress the system and bring the temps up but the fans do not respond at all, the fans are non pwm fans btw .

InfoSeeker

Senior Member

Mittwoch, 22. Juli 2015, 21:41

Could you post a screenshot of your controller setup?

garyd52

Junior Member

fan speeds by controller

Mittwoch, 22. Juli 2015, 22:22

Hi yes i'm not that savvy with screenshots but hopefully this will work.

InfoSeeker

Senior Member

Mittwoch, 22. Juli 2015, 23:55

Nice screenshot, except you excluded a point of interest, the"Source" to the left of the curve. :)


EDIT: a screenshot of the aquaero>fans tab would be useful also. (sample below)

Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »InfoSeeker« (23. Juli 2015, 04:27)

garyd52

Junior Member

Freitag, 24. Juli 2015, 12:30

Hi , the data source is an AC temp sensor located on the front rad and here is the fans tab
»garyd52« hat folgendes Bild angehängt:
  • fans.PNG

garyd52

Junior Member

Freitag, 24. Juli 2015, 12:34

i've done it again as I did'nt open the advanced settings in the first one
»garyd52« hat folgendes Bild angehängt:
  • fans 2.PNG

EnigmaG

Senior Member

Freitag, 24. Juli 2015, 16:20

I do´t see the Problem. By "Rear Rad outer" the spectrum is 46-89% Delta 43%
1% at the curve make 46+0,43%=46,43% at the fan
at start off your curve approximately 43% should it be 46+0,43*43=64,49% at the fan
At 95% 46+0,43*95=86,85% as it is in the first picture

Dieser Beitrag wurde bereits 3 mal editiert, zuletzt von »EnigmaG« (25. Juli 2015, 09:27)

InfoSeeker

Senior Member

Freitag, 24. Juli 2015, 19:39

Zitat von »garyd52«

i've done it again as I did'nt open the advanced settings in the first one


What was the temperature reading of the sensor you use for the fan controller?

I see you have the "rear rad outer" fan set to go no slower than 46% and no faster than 89% of the power range.
The fan is running at 86%, so you are basically running the max as you have it set in the fan setup.

If you specify 46% min and 89% max in the fan setup, the fan controller can only work within that range.

garyd52

Junior Member

Samstag, 25. Juli 2015, 15:13

Hi , you've solved it for me , I stuipidly ignored the fact that the fans are controlled by the controller lol, I had them turned down to minimise noise but have now set them except the hideously loud zalman reds to 100% and my curve is doing the rest , I sometimes cannot see the wood for the Trees and thank you both for your help.

Ähnliche Themen