Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
Did you manage to get this to work? My firmware is updated to 1003 and I used the 3 pin cable that comes with aquaero. Connected via aquabus 2 on both devices and still not seeing PA2 in Aquasuite 2012.. Where is the jumper on the PA2 and how do you set the address?
Edit: Ok, everything works cool now.Did you manage to get this to work? My firmware is updated to 1003 and I used the 3 pin cable that comes with aquaero. Connected via aquabus 2 on both devices and still not seeing PA2 in Aquasuite 2012.. Where is the jumper on the PA2 and how do you set the address?
When the PA2 is connected to USB, scan for usb device and then you have to set the ID in one of the software tabs in the original aquasuite software. I cant remember which one but i think its the 2nd or 3rd tab. Look for an ID of 50 in one of the tabs. The 1st PA2 you can leave at 50, every additional PA2 just increment the ID by 1. Remember to also apply the setting to the device to write the id into it. Remember to only do 1 at a time and disconnect aquabus until all units are completed. There is no jumper i think he is referring to the pairs of aquabus ports as jumpers. (you jumper from one PA2 to the next using the 2 3pin ports and the aquabus cable)
Dieser Beitrag wurde bereits 2 mal editiert, zuletzt von »pphx459« (26. Mai 2011, 12:12)
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »drbo« (27. Mai 2011, 13:42)
Still no success for me. I can not see any PA2s in Aquasuite, either in beta 1 or beta 2 (which I actually got working).
Any screenshot of what to look for?
drbo
I was so p... of not seeing my PA2 that i gave it a fresh start. Uninstalled beta 1, restart installed beta 2.
In the meantime, I had removed all usb connection to all Ac equipment except a5, and also Windows uopdate had a update for net4.
But after hooking all up with aquabus, the a5 restarts every few minutes.
But, any screenshots ...
drbo
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »drbo« (27. Mai 2011, 13:47)
powerjust -> high speed aquabus
multiswitch -> low speed aquabus
powerjust -> high speed aquabus
multiswitch -> low speed aquabus
That I know, I have my tubemeter and multiswich (y- cable) on the low speed (1)
and my three daisy chained PA2s on the high speed (2)
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Phatboy69« (27. Mai 2011, 14:25)
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Phatboy69« (27. Mai 2011, 14:33)
Make doubly sure you have connected the aquameter up correctly using the correct cable for the link to the Aquareo. The Aquaero cable connection, the number1 pin on the tubemeter (raised pcb one) has no wires out of it and the 2 black wires are connected to the number2 pin and the red ones therefore are connected to the number5 pin. The Aquaero cable connection that connects to the tubemeter has only 4 wires, some direct USB wire connections have 5 wires, so basically make sure that your red wire is connected to the number5 pin and then that should be correct.
-