Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Namron« (14. Oktober 2013, 17:58)
Are you sure the USB pump will work with a 3 pin cable? If the USB cable is not connected then the mps board has no 5V power. I think only the poweradjust devices use 3 pin aquabus because they have their own 5V supply from the molex connection.If you look at a picture of the PCB panel that's on the back of the ACD5 pump It's a 4 pin Aquabus... But you could use 3 pin also (the fourth pin just carries a 5v feed from the main Aquaero unit via the Aquaero USB that's connected to the motherboard) The fourth pin which is a 5v feed is useful for say the MPS Fill Level sensors if you don't want to keep having to recalibrate it each time you shut the pc down which you would need to do if you only used the 3 pin Aquabus.. Not all the MPS units that connect to the Aquaero Aquabus use 4 pins some use just 3 pins...
I Personally like to use the 4 pin Aquabus cables If the unit has the 4 pins on the PCB But have'nt seen any reason yet for the AC D5 pump to actually need a 4 pin Aquabus... It works perfectly fine using just a 3 pin Aquabus cable..
SO!!...In answer to your question about which type of Splitter cable to get for the Aquaero Aquabus I would recommend using the 4 pin Aquabus Splitter THESE As this then covers you for using both the 4 pin & 3 pin cable to attach the various MPS & Pump Aquabus's, As I pointed out above..... THIS IS FOR JUST THE AQUABUS MIND!!! & not the Fan headers... Hope that helps..
N.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Jakusonfire« (16. Oktober 2013, 02:45)
Hiya JakAre you sure the USB pump will work with a 3 pin cable? If the USB cable is not connected then the mps board has no 5V power. I think only the poweradjust devices use 3 pin aquabus because they have their own 5V supply from the molex connection.If you look at a picture of the PCB panel that's on the back of the ACD5 pump It's a 4 pin Aquabus... But you could use 3 pin also (the fourth pin just carries a 5v feed from the main Aquaero unit via the Aquaero USB that's connected to the motherboard) The fourth pin which is a 5v feed is useful for say the MPS Fill Level sensors if you don't want to keep having to recalibrate it each time you shut the pc down which you would need to do if you only used the 3 pin Aquabus.. Not all the MPS units that connect to the Aquaero Aquabus use 4 pins some use just 3 pins...
I Personally like to use the 4 pin Aquabus cables If the unit has the 4 pins on the PCB But have'nt seen any reason yet for the AC D5 pump to actually need a 4 pin Aquabus... It works perfectly fine using just a 3 pin Aquabus cable..
SO!!...In answer to your question about which type of Splitter cable to get for the Aquaero Aquabus I would recommend using the 4 pin Aquabus Splitter THESE As this then covers you for using both the 4 pin & 3 pin cable to attach the various MPS & Pump Aquabus's, As I pointed out above..... THIS IS FOR JUST THE AQUABUS MIND!!! & not the Fan headers... Hope that helps..
N.
Edit: I mean work with only a 3 pin Aquabus cable connected.
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Namron« (16. Oktober 2013, 09:15)
Hehehe.... I Know.... I can't believe it either ..... The only excuse I can come up with is....... It's been hard couple of days ....Namron
I can't believe you got things so ridiculously wrong I am seriously mad here
Just very kind of you to spend time helping a nutter noob like me out with this
-