Sie sind nicht angemeldet.
Lieber Besucher, herzlich willkommen bei: Aqua Computer Forum. Falls dies Ihr erster Besuch auf dieser Seite ist, lesen Sie sich bitte die Hilfe durch. Dort wird Ihnen die Bedienung dieser Seite näher erläutert. Darüber hinaus sollten Sie sich registrieren, um alle Funktionen dieser Seite nutzen zu können. Benutzen Sie das Registrierungsformular, um sich zu registrieren oder informieren Sie sich ausführlich über den Registrierungsvorgang. Falls Sie sich bereits zu einem früheren Zeitpunkt registriert haben, können Sie sich hier anmelden.
Duuugh! And I know why. LOL In an effort to manage my TinyPic space, and the space on my computer, I deleted the .jpg that I created from the .pdf. When TinyPic sync'd with my files, it also deleted it.
Wa3pnt: On my computer, the .jpg that you entered in the post above says "Tinypic (in bright colors) this image or video has been moved or deleted."
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Pastiche« (7. Februar 2014, 20:47)
or alternately produce an aquaero(7 ?) that has a dual 5.25" bay form factor that can accommodate more fan channels and also a larger screen that is touch enabled for better control on the aquaero itself. this would also take care of the aquaero master slave issue as one device would host all the fan channels you need. the cost, however, would be another issue.
Hi
Just got me a Aquaero 6 XT, its great that it has 4 x PWM fan connectors but i wonder is there anything in the pipeline for something like the Power Adjust that adds extra PWM fan channels since I technically need three more PWM channels?
I have a question similar to this question. There is only 4 PWM Fan channels and I have 2 PWM swifttech pumps and 3 PWM fans for each pump loop I understand that I will control each set of 3 fans for each loop together. I then have 4 sets of 2 120mm PWM fans to move air though the case with only 2 fan channels left how will I configure the system to accommodate the 4 sets of 2 120 PWM fans ????????
Taipan
unregistriert
Dieser Beitrag wurde bereits 1 mal editiert, zuletzt von »Taipan« (16. September 2014, 08:13)
Does anyone know what is the minimum rpm the AQ D5 with aquabus can go down to when connected to the Aquaero 6 XT?Will it function exactly as the swiftech 655 pwm
Hello. Just a quick question about the IR Transmitter output. I am wondering if you can program this IR to turn on an aircon unit when an ambient temperature sensor exceeds a certain value and to output an off signal once either the temperature goes below a certain value OR after a set time (to prevent the aircon turning on and off every 5min)? The controller would only need to 'learn" 2 IR commands on and off
Does anyone know what is the minimum rpm the AQ D5 with aquabus can go down to when connected to the Aquaero 6 XT?Will it function exactly as the swiftech 655 pwm
I do not know the rpm number but it would be useless anyway since it varies massively from pump to pump. The controller in our USB variant rebuilds the adjusting knob that a regular D5 pump has. So the speed range is the same as with a normal D5 pump.
By the way: Swiftechs PWM variant can not be used with the aquaero 6 because this pump does not follow the PWM standard and lacks the required 5V pullup circuit for the PWM signal.
Zitat
What if i tried placing a 10K pull up resistor and Zener diode from the PWM wire to the +5v rail.Can't we find out what the rpm range of the AQ D5 with aquabus is from the aquasuite? Thanks for all your help
Dieser Beitrag wurde bereits 4 mal editiert, zuletzt von »nicholas« (16. September 2014, 21:32)
The USB / Aquabus D5 is simply a D5 Vario with slight mods. It has the exact same min and max speed as any other D5 Vario (1800 - 4800). The PWM D5's can run at lower RPM's but that isn't very useful.Can anyone please help me?
Does anyone know what is the minimum rpm the AQ D5 with aquabus can go down to when connected to the Aquaero 6 XT?Will it function exactly as the swiftech 655 pwm?
Thanks in advance
-