• 21.07.2025, 17:52
  • S’inscrire
  • Connexion

  • Vous n’êtes pas connecté.

 

farbwerk - put color in your life! New 4x RGB LED controller

sebastian

Administrator

vendredi 29 mai 2015, 07:14

Citation de "Beercules"

what is the second aquabus connection used for?
This is only a bridged connector. When you have more than onde device you dont need a y-splitter.

Shoggy

Sven - Admin

vendredi 29 mai 2015, 09:12

Citation de "Blade Runner"

Can you connect RGB LED single bulbs to the Farbwerk or only LED Strips?
You could also use a single LED if it supports a supply voltage of 12V or you have to use a resistor. Keep in mind you have a common anode here.

psychotik2k3

Junior Member

jeudi 23 juillet 2015, 21:17

i just read that the farbwerk can measure voltage,
is that means that i can use it to read the hdd led signal from the mother board and replicate it to a strip ???
or will the variations be too fast for the unit to perfectly replicate the small amounts of light??

Hort

Junior Member

samedi 24 octobre 2015, 17:18

Hello. Do the farbwerk LED Strips blink on the Alarm condition like LED of the Aquaero? Is any additional setup needed?

Shoggy

Sven - Admin

vendredi 30 octobre 2015, 11:01

No, that is not possible. Might be possible in the future.

barfly

Full Member

farbwerk help

dimanche 22 novembre 2015, 23:52

hi
is there any how to manuals for the usb farbwerk version available as figuring the farbwerk out is horrendous.
Theres several ways to connect be it usb or via a aquabus but im wanting to control the led channels using sensors from the aquaero.
i can use aida 64 or hdinfo but the aquaero isnt sensors are not available
is there any work around using software or virtual sensors?
also can the farbwerk be displayed in the aquaero ui along with my fan,pump displays ect.
any help appreciated

Shoggy

Sven - Admin

lundi 23 novembre 2015, 11:25

farbwerk manual

The farbwerk settings can not be seen on the display of the aquaero.

Jakusonfire

Full Member

mardi 24 novembre 2015, 11:34

Am I reading the description of the v2 farby correctly that USB aquabus and Bluetooth are now combined instead of being Bluetooth or aquabus?

Shoggy

Sven - Admin

mardi 24 novembre 2015, 13:46

Yes, revision 2 can use aquabus and Bluetooth simultaneously.

Hort

Junior Member

jeudi 28 avril 2016, 08:55

Hello, does farbwerk require 5v power via molex connector? Will it work fine with a 12v-only power supply?

Ce message a été modifié 1 fois. Dernière modification effectuée par "Hort" (28 avril 2016, 08:56)

sebastian

Administrator

jeudi 28 avril 2016, 09:45

Citation de "Hort"

Hello, does farbwerk require 5v power via molex connector? Will it work fine with a 12v-only power supply?
The farbwerk need the 5V power to run.

Hort

Junior Member

jeudi 28 avril 2016, 20:30

Citation de "sebastian"

The farbwerk need the 5V power to run.

Citation de "Shoggy"


The farbwerk is designed to control LEDs with a voltage between 0 and 24 V. When installed to a PC system, the power supply will be 12 V so the LEDs or strips must be designed to use this voltage. Outside the PC and with an appropriate power supply unit, it is also possible to use 24 V LEDs.

Does this mean that external power suply should provide 24v and 5v? (I have never seen such power supply)

Discussions similaires