You are not logged in.
Dear visitor, welcome to Aqua Computer Forum. If this is your first visit here, please read the Help. It explains how this page works. You must be registered before you can use all the page's features. Please use the registration form, to register here or read more information about the registration process. If you are already registered, please login here.
Also die Kabel sind 1x rot (plus, 12V?), 2x Schwarz (minus?) und 1x gelb (Erde?).
Nein, gelb ist 12 V, rot ist 5 V, schwarz ist Masse. Oh Mann![]()
This post has been edited 2 times, last edit by "boli" (Jan 4th 2019, 5:41pm)
This post has been edited 1 times, last edit by "DaLiu" (Jan 4th 2019, 8:43pm)
This post has been edited 1 times, last edit by "Hannus" (Jan 4th 2019, 9:56pm)
Should be fine, but if you don't want to worry get a PWM splitter/hub with additional power from SATA or MOLEX.Hello,
I am planning to buy Aqua-Computer D5 NEXT Pump (mounted on HEATKILLER Tube 200 D5), do you think it's possible if I buy also Aqua-Computer SPLITTY9 to control all the fans (6 x NF-A12x25 PWM) speed and create a curve based on the water temperature for the pump and the fans? Need to mention I have 0 experience with watercooling, I am just planning my first loop.
Is SPLITTY9 mandatory to control 6 PWM fans from the pump or do I have some other cheaper solution?
Moin,
So habe nun auch die D5 next und ein kleines Problem:
Im Standby kommt der 12v Alarm (nur im Standby)
An Sata angeschlossen derzeit:
D5 next
RGB vom Gehäuse
1 SSD
PWM HUB
Netzteil: BQ DPP 11 650W
Verursacher scheint der RGB-Sata-Power vom Gehäuse zu sein. Zieht man diesen nämlich ab bleibt der Alarm aus.
System bootet normal und auch die Pumpe scheint sich normal zu verhalten. Ich nehme mal an wäre die Versorgung zu knapp würde der Alarm ja auch bei laufendem System angehen.
Jemand so etwas schon mal erlebt?
![]()
JaKann ich die Pumpe gleichzeitig auch noch per USB anschließen?
Für RGBpx muss eine dauerhafte USB-Verbindung bestehen.Wie es scheint muss ich den USB Anschluss einmal gebrauchen, damit ich das Display und vor allem das RGBx konfigurieren kann?!
So steht es in der Anleitung.Außerdem: Ist es korrekt das während der Kalibrierung des Durchflusssensor der Kreislauf komplett unterbrochen werden muss?
Angel4u
Unregistered
This post has been edited 6 times, last edit by "Angel4u" (Jan 9th 2019, 8:50pm)
This post has been edited 4 times, last edit by "Haadis74" (Jan 19th 2019, 8:01pm)
Hallo zusammen
Beim ersten Ablösen des Elektronikteils von der Pumpe hat sich bei meiner Pumpe auch gleich der kleine innen liegende Deckel der Pumpe mit gelöst. Beim erneuten zusammensetzen ist mir dann ein grünes Kabel, welches mit einem Miniaturstecker versehen ist, frei durchs Gehäuse zappelnd aufgefallen. Ich konnte jedoch nirgends einen Pin finden, an dem das Kabel wieder angeschlossen hätte werden können. Könnte mir vielleicht jemand sagen ob das Kabel, welches auf ein kleines Drehpoti geht überhaupt angeschlossen werden muss?
Vielen Dank & Grüsse
I am using the exact same Setup and it works absolutely fine.
Quoted
Hello,
I
am planning to buy Aqua-Computer D5 NEXT Pump (mounted on HEATKILLER
Tube 200 D5), do you think it's possible if I buy also Aqua-Computer
SPLITTY9 to control all the fans (6 x NF-A12x25 PWM) speed and create a
curve based on the water temperature for the pump and the fans? Need to
mention I have 0 experience with watercooling, I am just planning my
first loop.
Is SPLITTY9 mandatory to control 6 PWM fans from the pump or do I have some other cheaper solution?
Thank you very much!
This post has been edited 1 times, last edit by "Martlu" (Jan 21st 2019, 1:13pm)
-